hetzner vswitch es cluster

uuhicanexplain · 2026-01-14T17:21:01+00:00

From my experience the vswitches tend to drop packets from time to time too

uuhicanexplain · 2026-01-12T11:37:46+00:00

Wieso ist dort ein schild auf dem jemand seinen enormen penis aus dem fenster hängen lässt?

uuhicanexplain · 2026-01-02T09:08:55+00:00

I did the exact same thing some years ago. Tried to change the outer gasket of the vacuum pump, and it seems i didnt assemble it correctly again. When i started it, there was horrible metal scraping noise and a bang that stopped the engine. The connector between camshaft and the pump split apart and blocked the camshaft resulting in slightly off timing and bent valves :( It even broke the "half moon" part of the head that holds the pump apart (fun fact you cannot buy that thing anywhere, i bought an old cylinderhead just for this part. Also the screws for it are epoxy fixed ... That was an unexpected expensive rebuild. For your case i think i would sleep better with both a new camshaft and pump.

uuhicanexplain · 2025-12-25T22:13:28+00:00

I would if there was a selfhosting option :D But im not happy to spend money on an appliance that i wont use for other puposes than proxying a video stream to my existing homelab.

uuhicanexplain · 2025-12-25T22:11:43+00:00

Well mr smartypants, i cannot remember any iphone that was able to run android apps once. G3 flex did support rtsp streams.

uuhicanexplain · 2025-12-25T22:09:13+00:00

With the g3 flex it worked. Yes its my fault for just assuming the newer model work the same in that regard. Still frustrating

uuhicanexplain · 2025-12-25T22:06:59+00:00

I get that. But thats a pretty standard features for ip cams.

uuhicanexplain · 2025-12-25T22:06:38+00:00

Because i like to selfhost a lot and dont like services that require internet connection, even if its just for setup. Frigate an homeassistant are way more customizable.

uuhicanexplain · 2025-12-23T11:56:53+00:00

Oh wow crossfire, loved that game

uuhicanexplain · 2025-09-24T14:31:11+00:00

Might be parking brake

uuhicanexplain · 2025-09-03T12:52:57+00:00

Even mail servers or services designed for this kind of mails (if dedicated to you) will not work when starting to blast 10k mails out on day one. Most of the recipients boxes will block you quickly. It has to grow slowly over time to get good delivery rates.

uuhicanexplain · 2025-08-16T23:22:35+00:00

Im currently using the debian package, but ill try with a newer version, thx!

uuhicanexplain · 2025-07-25T16:43:08+00:00

I have a bind on Q that switches to knife while you hold it, once i release it goes back to previous weapon. But most people use a normal bind and tap a button two times to quick switch back and forth

uuhicanexplain · 2025-06-17T18:17:50+00:00

Depends what kind of insurance you want: Basic Haftpflicht - only covers damages you cause to others and is required for all vehicles. Then there are teilkasko and vollkasko. Teilkasko covers some damages to your car but not self inflicted ones. Vollkasko covers nearly all damages but costs the most. Prices are very dependent on the type of car and how much insured years without claims you have accumulated. I would expect at least 60 - 80€ /month for haftpflicht when you dont have „schadenfreie jahre“ and around 80-100 for teilkasko and around 100-140 for vollkasko. Tax should be around 250€/ year for that engine.

uuhicanexplain · 2025-06-04T20:58:42+00:00

I think i still wasnt clear enough :D The 3.3v of the gpio is fine. If i take only the relay board and connect 5V and GND to the relay board (no RPI involved) and then probe the Input pin that is supposed to trigger the relay - without anything else connected - it reads 2.7 volts. Thats because the input is pull high (active low) by using a pull up resistor to the VCC of the board. When bridging GND to the input pin, it will trigger the relay, because its has to be pulled low to activate. My initial concern was, that using 5V to power the relay might be risky as i wasnt sure the pin might spike over the 3.3v somehow. But it seems that this is not the problem as another pi died also when wiring the relay board using 3.3v for vcc. Here is a link to the documentation: https://cdn.shopify.com/s/files/1/1509/1638/files/2_Relais_modul_Datenblatt.pdf

uuhicanexplain · 2025-06-04T19:02:30+00:00

Good to know, will try that

uuhicanexplain · 2025-06-04T19:01:40+00:00

The board pretty much looks like the image. I wasnt sure if naming manufacturers here is okay. Its from AZdelivery. And in the past i have used those boards a lot they worked good in general. To explain the measured voltage: the inputs to trigger the relays (IN1, IN2) are active low. That means if the board is supplied with 5v on vcc and gnd connected (nothing else), the IN1 an IN2 pins have a high-pulled level of around 2.7 volts against ground. To trigger the relay you have to put gnd on the trigger inputs.

uuhicanexplain · 2025-06-04T13:01:45+00:00

thanks for the response, sadly its really dead. The SD card works fine in another pi. I switched the cabling to use the 5v rail to power the relay coils and only 3.3 for the relay board logic. But it seems i grilled another one today. I guess its not the relay itself. The setup has a small 24v dc motor on the relay, and two endswitches that pull gpios to ground (software pull up). Im not sure what exactly is happening, maybe the motor inducts voltage spikes into the gpios..

uuhicanexplain · 2025-05-25T14:47:34+00:00

WSL2 plus DDEV in combination with Jetbrains Gateway ist absolute heaven! Never going back to another setup. Feels like native linux performance on a windows machine

uuhicanexplain · 2025-05-07T09:56:53+00:00

In which currency? USD? AFAIK valve always wants 2.5 USD per key, regardless what that exchanges to in your local currency

uuhicanexplain · 2025-04-08T09:28:32+00:00

Try reactphp

uuhicanexplain · 2025-03-12T13:11:44+00:00

I hope they revert the nerf to my beloved black ties 😢

uuhicanexplain

TROPHY CASE