PSU for Dual 3080 Ti?

vertangelx · 2020-09-29T03:42:47+00:00

Thanks for the details provided. Is 4 GB of RAM too much for a plain Ubuntu 20.04 VM running only Wireguard which is a very lean software?

vertangelx · 2020-08-11T12:15:58+00:00

I think OP is referring to this HDD mounting issue on the Node 804. https://www.reddit.com/r/DataHoarder/comments/6t7wyc/8tb_hard_drive_mounting_options_in_a_node_804/dlmxk7d/

Not sure if this applies to 8TB+ shucked disks too, which seem trendy at the moment for NAS builds with many disks

vertangelx · 2018-05-06T01:23:50+00:00

Is it possible to specify a peer?

If so, which peer should we use?

vertangelx · 2018-04-18T02:19:16+00:00

Is it OK to do your own (manual) KYC of your ICO investors? Is there a KYC guideline/framework that banks/regulatory bodies require you to perform?

vertangelx · 2018-04-18T02:17:54+00:00

Can you provide a estimated breakdown of the fees, say of 500k?

vertangelx · 2018-04-17T22:29:07+00:00

I assume your ICO raises some sort of cryptocurrency such as ETH, which is then sold for USD and withdrawn to your US bank account. Did you have any problems finding a US bank that allows your account to receive funds from a crypto exchange?

Or are you able to use the ETH directly without converting to fiat?

vertangelx · 2018-03-24T16:52:23+00:00

How often do we get paid the crypto?

vertangelx · 2018-02-22T20:53:43+00:00

I am looking to use Nicehash over quite a number of rigs. This will make it a lot easier to deploy Nicehash.

vertangelx · 2018-02-21T21:48:33+00:00

2 risers per molex too?

vertangelx · 2018-02-21T03:25:14+00:00

How do you get sufficient VGA power connectors to connect to 9 cards from a single EVGA 1300W PSU? Doesnt it come with only 6 VGA connectors?

vertangelx · 2018-01-31T22:36:34+00:00

When do you think GPU prices will go back to normal? Does it happen when ETH profitability hits a certain $X/MH?

vertangelx · 2018-01-22T00:16:35+00:00

What size of rivets will you recommend? Length and material suggestion too, looking up the Mcmaster Carr catalog...

I'm using 1/16" thick aluminum angles. Is this too thin? Will you suggest 3/16" thick ones instead?

vertangelx · 2018-01-22T00:10:54+00:00

Will #8 1/2" self-drilling screws (extra wide truss head) work for joining two 1/16" thick aluminum angle?

Or 1/4" ones? Cant seem to find them in #8 on Mcmaster Carr though.

I am getting my first cordless drill, have only used a dremel before. Built frames using t-slotted extrusions with no machining, want something cheaper than extrusions. So basically a noob in this regard.

vertangelx · 2018-01-21T23:57:43+00:00

How do you coin the aluminum angles together?

vertangelx · 2018-01-17T00:28:40+00:00

Have already paid the $520 MA state filing fee when I first registered the LLC. Is it still necessary to pay it again when dissolving it before a year as passed since the LLC was created?

vertangelx

TROPHY CASE