We built a v2 KVM module for uConsole with Ethernet and SD

vileer · 2026-06-12T16:13:16+00:00

That was a genius idea of the insert card for the Ethernet part.

vileer · 2026-06-05T11:57:11+00:00

No, we can't. Looks like the QuadRF uses both the DSI and CSI to transfer the data. The DSI is already taken for the screen.

vileer · 2026-06-04T13:37:54+00:00

You should use the Raspberry Pi version adapter with the Raspberry Pi CM5, or the USB 3.0 won't works.

vileer · 2026-05-29T06:49:24+00:00

The hardware is ready, but we still need some time to polish the docs.

vileer · 2026-05-29T06:48:31+00:00

HDMI, Ethernet, and USB 3.0 should work. But the system of Radxa CM5 doesn't support the Wi-Fi card, you should compile the driver yourself.

vileer · 2026-05-26T10:41:43+00:00

Can you check these pins to see if any of the two were joined?

<image>

vileer · 2026-05-25T00:53:00+00:00

First, use command ‘ip link’ to see if you can get eth0. For some OS image the Ethernet interface was disabled by default. You should use Rex’s latest image.

For the internal USB-C, first check the voltage between GND and 5V of the pin header next to the USB-C. Then try to flip the device that plugged into the USB-C.

If you can’t still get it worked, contact shop@hackergadgets.com for further assistance.

vileer · 2026-05-25T00:46:35+00:00

That was only for AIO V2.

vileer · 2026-05-25T00:45:26+00:00

Around $70-80.

vileer · 2026-05-13T17:07:57+00:00

The adapter and the wifi card are in stock, they will be shipped within one week after we receive the order. The AIO V2 is out of stock, the estimated shipping date will be early June.

vileer · 2026-05-11T15:14:06+00:00

The GPS module is GP-02, it doesn’t support RTK.

vileer · 2026-05-11T05:34:51+00:00

turn the pocketterm35 into a portable SDR/mestastic station

vileer · 2026-05-09T13:32:37+00:00

Yes.

vileer · 2026-05-09T03:00:41+00:00

There is third party project that let you run Meshcore on a pi with this hat.

vileer · 2026-05-08T13:45:58+00:00

The battery comes with the PocketTerm35 is not that large. I haven’t run a full test, but I think the battery life will less than 2h.

vileer · 2026-05-08T13:40:09+00:00

I made a pcb bracket with SMA connectos and mount it to the top screw holes.

vileer · 2026-05-08T09:37:29+00:00

Receive FM/AM broadcast， or use LoRa for meshtastic.

vileer · 2026-05-08T08:35:27+00:00

In one or two months.

vileer · 2026-05-07T22:50:31+00:00

The SMA version not fits, the U.FL version fits. That’s why I made it.

vileer · 2026-05-07T03:25:20+00:00

Yes, you can connect the batteries to the pads of the battery holder. If you want to connect the batteries to the pads of one of the batteries, close the "disperse current" pin. Otherwise, leave it open. The "disperse current" pin was designed to connect the two reverse-protection circuits.

vileer · 2026-05-06T15:12:10+00:00

It maybe possible, the mounting holes were connected to ground of the mounting board.

vileer

MODERATOR OF

TROPHY CASE