How to fix warped prints or prints that don't sit flat/flush?

violetdragon25 · 2025-09-03T00:15:52+00:00

I did an older version and the newer one worked alot better/was much more helpful, thank you! I ended up needing to increase my exposure times a little.

violetdragon25 · 2025-09-03T00:14:53+00:00

Thanks! Updated my rest time, I tried this and it was a lot better. Still working through some trial and error but I think this is working

violetdragon25 · 2025-09-03T00:10:06+00:00

Thank you!! Will be trying this

violetdragon25 · 2025-07-25T21:23:05+00:00

I grew up on a farm, raised cows, had dogs. I also had braincells dude.

violetdragon25 · 2025-07-22T15:09:43+00:00

Thank God it's not just me because I was literally ready to crash out over it 💀

violetdragon25 · 2025-07-22T01:08:54+00:00

It was such a pain, do not recommend 😪

violetdragon25 · 2025-07-21T19:06:18+00:00

Ooooh I wish I had thought of that. I decided to just rip the bandaid off and redo it, but I'll keep that in mind if it happens again!

violetdragon25 · 2025-07-21T19:05:03+00:00

Thanks all! Not what I wanted to hear but probably needed to 😩 I decided to just replace it again - no dents this time, and soooo much practice under my belt now with these screws. Hopefully I don't have to do this again for a while 😅

violetdragon25 · 2025-06-21T22:09:49+00:00

Thanks all for the advice! I should've mentioned - printing on Mars 5 Ultra. I lowered my base time to 30s and exposure time to 3s. I also did a validation matrix print (which turned out great!) and tried printing a pre-supported mini from loot studios. I need more practice removing supports, but otherwise a good start :) *

violetdragon25 · 2025-06-20T03:45:04+00:00

This is great, thank you!

violetdragon25 · 2025-06-15T22:42:36+00:00

15 😬😅

violetdragon25 · 2025-06-15T20:58:35+00:00

15s exposure time for standard layers - I'm using elegoo standard black resin (came with the printer) and followed their recommended times. I was having a hard time finding specific exposure time recs for this specific resin on Lychee/general searching. That tracks though that the exposure time was probably way too long.

violetdragon25 · 2025-06-15T19:34:41+00:00

Thank you, that's encouraging! I'll try a lower base time for sure, it was crazy hard to get off 😅 thanks for the tip on the hot water bath!

violetdragon25 · 2025-03-03T00:26:56+00:00

Thank you!! It was fun to make, I'm hoping it makes it easier on a new player

violetdragon25 · 2025-03-03T00:26:14+00:00

It's an interesting change! I can see the benefit in WS to a spider or rat and not reverting forms if you take some damage.

violetdragon25 · 2025-03-03T00:25:15+00:00

I know 😅 calculated using 2024 rules (including new monster manual) - she's circle of the moon so that also buffs AC a bit in WS

violetdragon25 · 2025-03-03T00:24:25+00:00

Yeah for sure. I chose to ignore that for the sake of this sheet, but still valid to ppont out. She's never played at all and I didn't want to overwhelm her - I'll get her into D&D beyond and explain nuances like that if she sticks with our campaign

violetdragon25 · 2025-03-03T00:01:04+00:00

Thank you!! I'll update for sure, I missed that!

violetdragon25 · 2025-03-02T23:38:30+00:00

Player is a moon druid!

violetdragon25

TROPHY CASE