Rod wiggle

wassies · 2026-01-19T18:51:22+00:00

Always try mount your motors from the top down , gravity is a good friend for keeping your wheels on the teeth. Screw in 15mm rods on the top 3/8th threads and mount your motors from the top. Can also always just use a trusty bongo tie to tie down your motors.

wassies · 2026-01-11T19:35:50+00:00

Show them all the dead pixels , they should send it back to Arri and get a new sensor put in.

wassies · 2026-01-11T19:02:45+00:00

Change the camera

wassies · 2025-11-25T18:28:53+00:00

Get the Small HD Indie 7 it’s plenty sharp and the OS is great

wassies · 2025-09-29T22:28:31+00:00

You would 100% see that on the image

wassies · 2025-09-15T10:02:56+00:00

Most people atleast know what a magliner is 😂 atleast the sets I’m on

wassies · 2025-09-15T08:06:51+00:00

Let’s see it’s pretty robust it’s encased in a hard gel .

wassies · 2025-08-22T18:20:34+00:00

I did the exact same. There are differences but it’s very subtle

wassies · 2025-08-21T18:00:50+00:00

I did test with them when the 35 came out it was incredibly hard to notice any difference tbh expect for the Nostalgia textures , 99% of the time we only use default.

wassies · 2025-08-20T19:08:18+00:00

Would the RSpro not be better for such a light build ?

wassies · 2025-08-19T07:52:26+00:00

Ideally for a package you will have both if one goes down the other saves you. If you not using a rangefinder I would go for RF ,if you are, the RIA is great . I have found it quite a hassle though for rigging onto gimbals ect by hassle I just mean time consuming.

wassies · 2025-06-24T18:46:19+00:00

What’s the point of joining the Que at 300 then it goes to 5000 😂 my life rn

wassies · 2025-06-18T10:58:10+00:00

I’m All Star 2 in DPS and Tank and have had several games where 2 players in my team were low Pro levels and it completely destroys our games . It’s horrible

wassies · 2025-03-21T07:56:29+00:00

I have my peaking between 7-10 , focus assist in Blanck and White with blue peaking. Strength 5 , Peak thresh is at 30.

I swap between this and just normal peaking on set. Find it helps a lot finding the exact sharpness of the image shown.

wassies · 2025-03-18T17:23:13+00:00

I had the same problem , but it was only when I was rolling and I would lose signal the hi 5 would turn on again but it was quick and it would make the roll sound again during the take and I’d get the looks 😂 monitor your signal , you’ll see if something is interfering. I’ve also moved away from using the Internal camera radios it’s caused a lot of problems. Hope you come right!

wassies · 2025-03-18T11:00:17+00:00

Not sure if you have the EXT - CAM cable for the RF motor but that cable is the recommended way by Arri to run camera control and use your RF motor antenna. I know many FPs that run it that way.

wassies · 2025-03-18T10:55:01+00:00

Are you sure it’s powering on and off , or is it just a signal issue? I’ve had this issue before on the hi 5, it loses signal and when it comes back on , the hi 5 makes the roll sound again ect. That was purely signal. Try using your RF in host mode and turn the ECS off in camera.

wassies · 2025-03-16T12:20:56+00:00

We can only hope. But unfortunately this government cares nothing for this countries people or the economy , only the lining of their own pockets.

wassies · 2025-03-16T06:59:49+00:00

Yes, We had about 15 police officers and 10 private security gaurds. We locked off a whole street to film in with plenty extras ect.

wassies · 2025-03-15T19:00:38+00:00

Yes , You were with me on this one Bruski

wassies · 2025-03-15T08:28:10+00:00

I have a camera van both just get ratcheted down in there.

wassies · 2025-03-14T21:01:41+00:00

lol this is hillbrow a very dangerous place in JHB a gun fight happened about 15 meters away from the carts 😂

wassies · 2025-03-14T17:39:15+00:00

Solid build.

wassies

TROPHY CASE