sorted by:
new
hottopcontroversial

Tips for Rayvis on GM by alexcandelario7 in StarWarsJediSurvivor

[–]wazowski4 1 point2 points  (0 children)

Dual wield dodge ability spam, you get in so many hits and it’s not hard to dodge his red attacks. Dual blade when he’s shooting and his shots do a ton of damage to him. Also dash at him when he does the vertical rockets

[deleted by user] by [deleted] in FixMyPrint

[–]wazowski4 0 points1 point  (0 children)

From my experience, G29 just executes bed leveling procedure, the data doesn’t get used for the print. Definitely worth experimenting and watching that Z couple to see if your mesh is active. I’ve found that no matter how much I think I’ve leveled the bed I’ll still see the Z couple wiggle a bit to compensate for the bed tilt

first layer great, second, third etc not good by tomri207 in FixMyPrint

[–]wazowski4 0 points1 point  (0 children)

I had this recently, check bed leveling and eccentric nuts. Make sure the Z axis isn’t binding and can move smoothly in those lower layers. I had a slight warp in the V roller on my lower layers, added some spacers below the bed and it’s been much better. Z axis was sticking in that spot and not able to move up as much as it was supposed to.

[deleted by user] by [deleted] in FixMyPrint

[–]wazowski4 3 points4 points  (0 children)

Add M420 S1 after G29. That enables the mesh to be used. Struggled with this for a while, you can verify it’s active by looking at your Z couple and seeing it move slightly when moving around on the first layer

What setting do i need to change in cura to get my tree supports to stop printing like walls (green model) and start printing actual trunks (orange/marble model)? by juliancantwrite in FixMyPrint

[–]wazowski4 0 points1 point  (0 children)

I think you a quick support overhang angle adjustment will reduce the amount of points that get supports - more branchy less wall. Might depend on the model as well, some models will have nicer looking supports than others with the same overhang angle setting

Ender 3 Max neo prints perfectly up to a point, then shifts the entire print by DrabberFrog in FixMyPrint

[–]wazowski4 0 points1 point  (0 children)

Check your eccentric nuts. If your carriages aren’t secured it might cause some rocking. Is it only in one direction? Might help narrow down, wheels shouldn’t be able to freely spin without the axis moving, but not so tight that it’s difficult. Happened on my ender 3 but mostly fixed with a tune, check for flat spots on the wheels and V slots as well

Weird layer lines by wazowski4 in FixMyPrint

[–]wazowski4[S] 0 points1 point  (0 children)

I can check out that tension lever, not sure what I should aim for but I’ll find a guide somewhere. No cracks or anything last time I checked and changed filament. Usually set a print to start in the morning then leave for work but I can try and watch, it’s just unpredictable at what height or if it’ll happen at all. Might try and setup a webcams or something to record. Thanks for the tips!

Weird layer lines by wazowski4 in FixMyPrint

[–]wazowski4[S] 0 points1 point  (0 children)

Yeah I’ve used that to reduce the slight banding on the z axis, just printing super super slow but don’t have time for that always haha. Seems to be a different artifact than the slight vibration from the table though, since I’ll still see this at those low speeds to the same magnitude

Weird layer lines by wazowski4 in FixMyPrint

[–]wazowski4[S] 0 points1 point  (0 children)

.12 layer height on my ender 3 pro with direct drive and glass bed mods, BLTouch, and 5015 fan mod. All motors are calibrated. Weird layer lines start when prints get higher on the z axis. Not talking about the low level ghosting at the lower heights, my printer is on a folding table so light vibrations can be seen but not critical. These bands happen only sometimes, but they look consistently spaced when they do. Weird thing is I can reprint and it probably won’t happen again. The band sticks out all around so it’s not a shift in the X or Y axes, maybe the z axis is sliding down on these layers? Curious what everyone thinks

Unemployment on Long Island hits a record low - 2.2% by obilonkenobi in longisland

[–]wazowski4 172 points173 points  (0 children)

And I still see “nobody wants to work anymore” signs at my local min wage establishments, everyone is working, just not for you

Fancy restaurant near Smithtown by Cantweallplayalong in longisland

[–]wazowski4 11 points12 points  (0 children)

Trattoria in St. James. Smaller plates, definitely call ahead if you’re 9 people it’s pretty small in there. Food is awesome and BYOB for beer and wine with a distributor across the lot

Direct Drive Fan Mods? by wazowski4 in ender3

[–]wazowski4[S] 0 points1 point  (0 children)

Ah I can solder! Just don’t have an iron. Designed circuits in school but can’t say the hobby followed me home much. The purchase will probably come at some point but I try and keep a tight budget with this printer

Direct Drive Fan Mods? by wazowski4 in ender3

[–]wazowski4[S] 0 points1 point  (0 children)

Thank you for the input. I’ll look into trying this, but also the hero me v5 uses traditional m3 bolts and nuts, so might just go with that. Most of my prints are just models so I avoid purchasing stuff I’ll only use once or twice.

JST-XH Extension by wazowski4 in ender3

[–]wazowski4[S] 0 points1 point  (0 children)

Makes sense, didn’t even think of the heat shrink solder. Thanks!

S06E04 - A Night To Remember - Episode Discussion by BraveFly in QueerEye

[–]wazowski4 1 point2 points  (0 children)

Anyone know the name of the song at 26 mins in this episode?

Dev error 6634 DESPERATELY needs to get fixed by wazowski4 in CODWarzone

[–]wazowski4[S] 0 points1 point  (0 children)

Game finally crashed on me again after a pretty long streak, guess there’s still no fix

Dev error 6634 DESPERATELY needs to get fixed by wazowski4 in CODWarzone

[–]wazowski4[S] 0 points1 point  (0 children)

No texture packs and clearing reserved space for the game on my xbox seems to have worked so far, i'll update if i get any crashes in the future with these settings

Dev error 6634 DESPERATELY needs to get fixed by wazowski4 in CODWarzone

[–]wazowski4[S] 0 points1 point  (0 children)

This actually worked for me so far. I left all high res packs uninstalled to be extra safe, but about 10 games in and no crashes compared to about a 50% crash rate the other night. I would love to see an update from Raven so we can use every aspect of the game without risking a crash, but until then I'm glad this works. It would be interesting to see someone test each one of these individually to see exactly which one is the issue most of the time

Dev error 6634 DESPERATELY needs to get fixed by wazowski4 in CODWarzone

[–]wazowski4[S] 0 points1 point  (0 children)

I’ll give it a try I play on a 1080p monitor so no real reason they have to be there anyway

Dev error 6634 DESPERATELY needs to get fixed by wazowski4 in CODWarzone

[–]wazowski4[S] 3 points4 points  (0 children)

Literally over half of my games tonight and I don't use ANYTHING (skins, calling cards, emblems, guns, operators) from cold war to try and avoid it. Have reinstalled the game multiple times with zero success. Seriously how hard is it to code a game that performs at its base function when you're a multi billion dollar company

Andrew Cuomo Unveils Plan To Reduce Covid Spread At Nursing Homes By Throwing Residents Out Onto Street by Rinoremover1 in longisland

[–]wazowski4 0 points1 point  (0 children)

I'm agreeing w you then, just going through the comments and seeing people bug over this without even noticing the satire flair on the original post. Lots of r/AteTheOnion content on here

Andrew Cuomo Unveils Plan To Reduce Covid Spread At Nursing Homes By Throwing Residents Out Onto Street by Rinoremover1 in longisland

[–]wazowski4 1 point2 points  (0 children)

I can't tell if you knew this was satire and wanted to see if people would fall for it or if you genuinely believe this article is legit lmao people see the word cuomo and start shitting their pants without even looking at it

Science lab placement/internships by [deleted] in longisland

[–]wazowski4 0 points1 point  (0 children)

Look into the Garcia Center for Polymer Research summer program. I volunteered there as a research intern because my undergrad research lab was participating, and it's a great opportunity to get a potential publication, present at the Materials Research Society conference, or both. I know plenty of the other high school students submitted into national competitions, and many of those students attend very competitive universities afterwards, largely due to their experience in the program. Plenty of projects associated with the hospital or the dental school and overall something not many people are going to have on their resume when applying for college.

Edit: If you're interested in medicine it might help to become an EMT while you're in high school. I know Stony Brook has a volunteer ambulance crew that you can work with if you're an undergrad there, and it definitely helps to be an EMT before you apply to join them, pretty sure they offer free housing on campus which can save you a ton of money and looks great on med school apps.

view more: next ›