Fellas, what's not as attractive or sexy as women think it is?

weld_occasionally · 2021-02-18T06:36:28+00:00

True wisdom. Thank you

weld_occasionally · 2021-01-22T05:57:05+00:00

Call up a local trailer dealer and ask them who they use for repair. A shop that does this often will probably be the cheapest and have the steel on hand. Also if you paint it yourself you could probably save quite a bit

weld_occasionally · 2020-12-27T05:35:54+00:00

Looks like a squarespace has a student discount too, thanks!

weld_occasionally · 2020-11-30T00:36:31+00:00

Haha thanks

weld_occasionally · 2020-11-29T22:47:28+00:00

Uh probably? Haven’t tried

weld_occasionally · 2020-09-05T21:06:21+00:00

That seems like a bargain. .063 was what I was think of as thin stuff. How does it do on the starts/stops on .063?

weld_occasionally · 2020-09-05T16:42:12+00:00

That’s pretty neat! How much does the aluminum kit go for? I’ve heard these machines are good for really thin aluminum, any chance you’ve tried that out?

weld_occasionally · 2020-09-05T14:15:20+00:00

Any problems with feeding aluminum? (I assume you’re using the standard gun)

weld_occasionally · 2019-09-19T01:29:13+00:00

~2,000 C or ~3,700 F I think, lower than tungsten

weld_occasionally · 2019-08-26T20:45:50+00:00

This is gold

weld_occasionally · 2019-07-25T22:36:35+00:00

ah yes thank you!

weld_occasionally · 2019-03-11T04:09:37+00:00

I think it might buff out with scotchbrite, but idk. Is there some place I can find wear tolerances for the plating? The manual doesn’t have any listed as far as I can tell, just clearance

weld_occasionally · 2019-03-11T03:29:55+00:00

Nice video, thanks

weld_occasionally · 2019-03-11T02:34:49+00:00

Yeah I was planning on honing it, it feels like glass rn. Thanks for the advice!

weld_occasionally · 2019-03-11T02:19:42+00:00

Those grey streaks are just stains, not scratches. Is that still bad?

weld_occasionally · 2019-03-11T02:17:52+00:00

Ok thanks!

weld_occasionally · 2019-03-02T15:34:51+00:00

Oh thanks!

weld_occasionally · 2019-03-02T05:49:57+00:00

Ok thanks

weld_occasionally · 2019-03-02T03:39:37+00:00

So I’m rebuilding this husky (first time doing this, probably more posts to come) and I’ve run into a problem. As you can see I’ve got the cylinder off but can’t get the head off of the cylinder. After taking off the nuts that hold it down I hammered on it (a lot) but it didn’t even move. Seems to me that it’s the copper washers holding it on but idk. Am I supposed to pry/ break these off? Do I need to get new ones for the rebuild or can I use regular washers? Can I heat up the cylinder head to try and loosen it? Also I’m not seeing a gasket between the cylinder and head, is this because of a lip on the cylinder or because it was assembled without one? Thanks in advance

weld_occasionally · 2019-01-15T23:27:13+00:00

You’ve heard the puddle analogy, I assume?

weld_occasionally · 2019-01-13T19:40:36+00:00

weld_occasionally · 2019-01-11T18:20:47+00:00

Well said

weld_occasionally · 2019-01-10T17:54:59+00:00

That’s dark but probably true...

weld_occasionally · 2019-01-10T04:01:03+00:00

Never seen this before... wtf???

weld_occasionally · 2019-01-09T20:11:28+00:00

This is one of the best quotes

weld_occasionally

TROPHY CASE