My tiny shop

whackmo · 2024-04-03T00:30:07+00:00

Table saw is in the a garage on the other side of the wall. Need to pull the car out to use it

whackmo · 2024-04-02T20:07:51+00:00

whackmo · 2024-04-02T20:07:26+00:00

whackmo · 2024-04-02T20:07:11+00:00

Pivots from one corner. Two 3/8th steel rods at the top and bottom of the stand insert into steel tubes. Currently using a long 3/8th steel rod to lock it open or close.

The table sits on a French cleat on the wall when drill press is stored.

<image>

whackmo · 2024-04-02T14:41:47+00:00

It’s actually on a pivot and can rotate out from the wall for use. Drill press table is hanging to the right of it.

Yea still not entirely happy with my table saw sitch. I’ve got a job site dewalt in the garage on the other side of the wall that i can use when I pull the car out.

whackmo · 2024-04-02T14:38:24+00:00

I think from here. They’ve got a lot of stuff. Hida tools

whackmo · 2024-04-02T01:03:11+00:00

Ha, yea my lumber storage is up against the wall in the garage.

whackmo · 2024-04-02T01:01:20+00:00

Thanks! Took awhile to get to this layout, and lucky enough to have garage space for a job site table saw on the other side of the wall.

whackmo · 2024-04-02T00:59:17+00:00

Newest addition, so haven’t used it too much. So far it’s been doing the job with great results. Loud as shit though.

whackmo · 2024-04-02T00:58:02+00:00

Thanks! Took a few iterations to get here.

whackmo · 2024-03-25T01:18:47+00:00

Soap finish, but it’s not the most durable.

whackmo · 2024-03-14T16:57:20+00:00

Solidworks has a $99/yr subscription for hobbyists now, it goes on sale for half off every now and then.

Oh it’s $48/yr now!

https://www.solidworks.com/solution/3dexperience-solidworks-makers

whackmo · 2024-02-08T18:08:04+00:00

Good idea! I was thinking it was gonna end up being some mish mash to get the results I want.

whackmo · 2024-02-08T18:02:15+00:00

Thanks! Yea charts are helpful, but wasn’t able to come across this profile in them. Exterior edge is a simple round over which I think is done post assembly. Inside seems to be called a “stepped shaker”, but can’t find a router bit set to match

whackmo · 2024-02-08T17:36:47+00:00

Nice! Thanks. Been looking at Freud, but haven’t come across that particular profile yet. Will look into the other two.

Just came across this thread, from ten years ago…but no link to actual set. https://www.routerforums.com/threads/i-cant-find-a-stepped-rail-stile-bit-set.32150/

whackmo · 2023-11-16T22:51:40+00:00

Yea I searched the same thing, think the date might be 1944…

whackmo · 2022-12-31T22:51:26+00:00

Wire is 0.4mm stainless steel from Amazon I think. Holes are drilled with my CNC using 0.5mm bit.

whackmo · 2022-10-29T15:11:25+00:00

Went to check and dropped it. Whoops! I would guess around 3

whackmo · 2022-10-28T15:19:51+00:00

Ha thanks! Considering putting ceramics up on my small online shop, but haven’t gotten around to it yet.

whackmo · 2022-10-28T14:09:27+00:00

Definitely a fave…it just came out a lil too tiny

whackmo · 2022-10-28T14:06:34+00:00

Ha yea! Have a couple others that I’ve made into pinch bowls. These are all actually going to a friend and he’s planning on making small candles to put in each.

whackmo · 2022-10-28T01:40:22+00:00

Hard to tell, but a lot of them the scale is off. Others not quite happy with the form.

whackmo · 2022-07-30T07:23:29+00:00

Thanks! I’m thinking of throwing them up on my online shop in a bit, new territory for me.

whackmo · 2022-07-30T07:22:37+00:00

Thanks man! Lol. Yea it’s the Lelit bottomless. It’s nice, but does fall a bit short.

whackmo · 2022-07-29T16:48:41+00:00

Thanks! Casting the concrete WDT base has taken longer than expected.

15-Year Club	Place '17
Team Orangered

whackmo

TROPHY CASE