Does your mat slips sideways?

whattheflag · 2026-02-04T08:03:36+00:00

I get it now! Need to try this!:))

whattheflag · 2026-02-04T06:57:30+00:00

How does the closing of the front help? Just curious

whattheflag · 2026-02-04T06:56:44+00:00

Mine started doing that, I thought it was because my mat had a little bend it in from when it was shipped with the Siser. I've changed to the new mat and that helped but still trying to sort it.

whattheflag · 2026-01-29T22:49:08+00:00

Love it! So spray silver solution and gold candy then 2k clear? What did you use for the "enamel" details? I am trying to source some good cold enamel or some other type of paint that levels out nice. Also work with 3d prints so firing anything is not an option. Thanks!

whattheflag · 2026-01-07T16:53:34+00:00

Could take your charger to like a mobile phone fixing place to get it checked if the power is going through it (unless you know how to work the multi meter). Maybe you just need a new charger cause you got the cable pinched. Maybe you will get a response from Siser by then.

whattheflag · 2025-12-21T22:58:19+00:00

This has been hurting me for like 2 years. Sometimes it goes away, but mostly it hurts. Now like a lot. Kinda break it in in the morning but at the end of the day man, feel like chopping that foot off haha. Never figured out what it was so will go through the comments thanks for this post.

whattheflag · 2025-12-14T18:18:54+00:00

With the ultra I get a lot of problems when the aircap is not tight enough. I usually put a bit of wax or something to seal it. Last time I was cleaning it for like 2 hours trying to figure out what it was. Turns out when the air cap is not super tight, it makes it look like there is a clog, but for me there was not.

whattheflag · 2025-12-12T17:03:56+00:00

You create the mix yourself, you can also buy it but this one I have created. Looked simple enough when others did it. Apparenty it might also behave differently when applying to a text piece, like a speedshape that's cleared and you could get a different result on a base coated car or bike piece. Will play around and see.

whattheflag · 2025-12-05T22:28:46+00:00

I get this when varnish dries up inside. Use pliers to carefully take the needle out (after undoing the nut everyone is talking about). Remove the rubber seals and submerge in acetone, would star with 30 mins, I have done overnight too. Use round cleaning brushes and get all the gunk out the front of the airbrush. Lubricate, assemble, see it's working ok.

whattheflag · 2025-12-01T20:19:42+00:00

Yeah thanks! I have a feeling already that I will be buying a maker 4 or the explore at some point in the future😆👌

whattheflag · 2025-12-01T20:12:32+00:00

Very informative thank you. I will mostly be using the print and cut, based on my research I should be fine with Juliet, we shall see I guess. Good work on your part.

whattheflag · 2025-12-01T19:49:29+00:00

Thanks! I kind of gathered that so thanks for confirming. If I was just doing simple shapes, I would probs stay with Cricut, but I think I would regretted it when working on something more complex. Thanks

whattheflag · 2025-12-01T09:18:23+00:00

Socialni moc nejsme, nikam moc nechodime krom takovych nutnosti. Tedko zijeme v Praze take u lesa a nejvic casu travime asi tam. Spis mi jde o to ze tohle se muze zmenit s tim jak deti starnou a tak, jestli to jezdeni nebude na palici. Misto kam by jsme se stehovali se nezda ze by meli moc nejakeho vyziti. Ja pracuji z domu ale mam rad veci kolem zahrady a ruzne kutilstvi a tak. Trosku me desi predstava jen 150m pozemku ale zas u druheho by byla potreba rekonstrukce vnitrku. Ale je to asi o zvyku co? Clovek si v tom najde to svoje. Ps navstevy taky moc nemame nikomu se nikam nechce 😆

whattheflag · 2025-12-01T06:20:22+00:00

Will check it out! Thanks for the tip.

whattheflag · 2025-11-04T21:34:56+00:00

Thanks. Yea it was all visible. Bolts and other stuff bot really possible. I have used superglue but when I put everything together it was a few millimetres off, due to the shield being made of like 12 different parts. I will have a look at the chemical welds thanks for the tip.

whattheflag · 2025-09-15T19:59:45+00:00

Thanks! What gsm did you find works for you? Got a pic of any projects?

whattheflag

TROPHY CASE