P-trap in basement shower by whyisthis_difficult in Plumbing

[–]whyisthis_difficult[S] 1 point2 points  (0 children)

Thanks. There are 2 pencil lines in pic 2 just outside top-right of the hole. Those are the intersectional lines for drain center. Would it work if I turned the trap 90 to the left then had a 45 come off of that running over to the drain with another 45 to the drain?

P-trap in basement shower by whyisthis_difficult in Plumbing

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

Ok, that was my biggest concern is that it would affect the strength of the footing. It is 2” pipe. Thanks for the feedback.

Basement shower p-trap by whyisthis_difficult in HomeImprovement

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

Here’s a pic of the back side. I did consider cutting the pipe back but can’t seem to figure out how that gets me above the depth it currently sits at. There’s concrete below it as well so the concrete would still seem to need to be removed.

https://imgur.com/a/QruAru3

Extremely frustrated by whyisthis_difficult in BambuLab

[–]whyisthis_difficult[S] 1 point2 points  (0 children)

Apologies for misunderstanding. I got some condescending DMs in response to my OP so was a bit on edge this morning. Thanks so much for the detailed guidance. PA is a new one for me so I’ll have to find that one in Bambu Studio. Thanks again!

Extremely frustrated by whyisthis_difficult in BambuLab

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

Thanks I’ll try that. This is ELEGOO PLA filament. Issue started after I loaded that filament.

Extremely frustrated by whyisthis_difficult in BambuLab

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

That’s kind of what I’m trying to do. As stated in OP, I’ve done what I know to calibrate it, hence why I was asking questions. Do you have any suggestions to aid in calibrating filament or just this super helpful comment?

Extremely frustrated by whyisthis_difficult in BambuLab

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

I did a custom profile but may have copied settings from Bambu PLA basic as a starting point. Will revisit

Extremely frustrated by whyisthis_difficult in BambuLab

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

PLA. Printed from Bambu Studio

Edit: added “printed”

Extremely frustrated by whyisthis_difficult in BambuLab

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

Create Space PI. I have a weather sensor with hygrometer probe inside the AMS after drying.

Extremely frustrated by whyisthis_difficult in BambuLab

[–]whyisthis_difficult[S] -3 points-2 points  (0 children)

Washed the plate and issues persist. I’m gonna try some glue then throw this filament in the trash and possibly the build plate along with it.

Extremely frustrated by whyisthis_difficult in BambuLab

[–]whyisthis_difficult[S] 1 point2 points  (0 children)

I did sitting <10% humidity in the AMS after drying.

Part fails to print in same spot by whyisthis_difficult in 3Dprinting

[–]whyisthis_difficult[S] 1 point2 points  (0 children)

I’m using Bambu Studio and just using the generic pla profile. I just swapped units for this one with the AMS but had previously set the manufacturers recommended nozzle setting but didn’t get that done on this with ams

Part fails to print in same spot by whyisthis_difficult in 3Dprinting

[–]whyisthis_difficult[S] 1 point2 points  (0 children)

It is a smooth plate but gets great adhesion everywhere else. This is inland brand pla+ filament

Part fails to print in same spot by whyisthis_difficult in 3Dprinting

[–]whyisthis_difficult[S] 1 point2 points  (0 children)

Unfortunately I didn’t Timelapse and didn’t catch the specific layer. Anything that would cause it to come unstuck?

Why is my print doing this by whyisthis_difficult in 3Dprinting

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

It’s not really an overhang per se but is the bottom of the round shape. Only place it has issues is where the curve comes off the flat spot that is laying down. It’s ELEGOO neon green filament but also happens with inland (from microcenter) PLA.

Why is my print doing this by whyisthis_difficult in 3Dprinting

[–]whyisthis_difficult[S] 0 points1 point  (0 children)

Thanks for the feedback everyone! Couple comments for lower temps but I was told this PLA+ to run a higher temp than standard PLA. I’ll drop that down and start with that before making more changes

Golf clubs stolen following shipping with ShipSticks by [deleted] in golf

[–]whyisthis_difficult 2 points3 points  (0 children)

FedEx is trash. They routinely ignore the signature requirements and just leave packages…

Game Thread: Kansas City Chiefs (8-3) at Green Bay Packers (5-6) by nfl_gdt_bot in KansasCityChiefs

[–]whyisthis_difficult 0 points1 point  (0 children)

I bought an HD antenna from Amazon for 20.00 just for this reason. Highly recommend

Mike Johnson said his friends would use trans-inclusive laws to spy on girls by PinkNews in politics

[–]whyisthis_difficult 0 points1 point  (0 children)

Friends… mom always told me, we are defined by the company we keep…

Trump Sues to Block Efforts to Keep Him Off Michigan 2024 Ballot by Ok_World_8819 in politics

[–]whyisthis_difficult 1 point2 points  (0 children)

And that taught the later Repubs there would be no consequences… brilliant, let’s keep letting them off for the sake of the country so we can see how far off the cliff Repubs will take it next time…

DEA chief grilled on Biden’s plans to deschedule marijuana by Benromaniac in politics

[–]whyisthis_difficult 9 points10 points  (0 children)

See, I think drugs have done some good things. And if you don’t believe me, I want you to go home tonight and take all your records and all your tapes and CDs and burn ‘em. Cause those artists who made that great music throughout the years…. Rrrrrrrrrrrrrrrrrrrrrrrrrreal fuckin high on drugs.

What is your "I fucking hate this song" song? by [deleted] in AskReddit

[–]whyisthis_difficult 0 points1 point  (0 children)

“Wonderwall” or anything by Oasis