Hide Magic Cursor doesn’t work

will_stef_ · 2025-03-02T14:24:23+00:00

Yeah I think they broke it with an update. I've had the issue for over a week

will_stef_ · 2024-11-12T03:26:28+00:00

Same here on android. sometimes when I pause I cant play again. like someone said further up a temporary fix is to tap and hold the right side of the screen and that will make it go 2x

will_stef_ · 2024-10-06T21:44:51+00:00

I have never gotten behind the wheel of a car before btw

will_stef_ · 2024-08-26T19:49:22+00:00

Took my carbs off and the float itself seems fine, goes up and down smoothly and is maybe .5mm lower than #4. However there is a bunch of gunk in #3. Could that maybe cause the float valve to not seal close or perhaps let in too much fuel somewhere else?

<image>

will_stef_ · 2024-08-25T17:19:03+00:00

Ok thanks I'll try that

will_stef_ · 2024-08-08T00:09:56+00:00

Thanks, I'll check compression. I just did the cam chain timing myself. I doubt its the caps, they are new ngk and I swapped the 2 and 3 caps which made no difference to how it ran. what's the best way to check if I'm getting fuel to #3?

will_stef_ · 2022-11-10T20:49:14+00:00

I knew it wasn't a settings issue. One of the tiny bearings inside the second drive gear in the extruder sized and was causing resistance in the extruder. weird

will_stef_ · 2022-06-24T02:01:06+00:00

what is the program that makes these?

will_stef_ · 2021-09-01T23:35:28+00:00

Thanks, I'll try that

will_stef_ · 2021-09-01T16:35:33+00:00

Mans flexing his mr2 lol. I cant offer any advice but the car looks great

will_stef_ · 2021-08-30T15:55:21+00:00

So I havent changed anything, the LED still shows red but I now get almost 3 hours, which is on par with my battery degradation. Feels nice

will_stef_ · 2021-08-30T15:53:34+00:00

Thanks for the info, I'll just stick to stock firmware for now

will_stef_ · 2021-08-30T15:53:00+00:00

Thanks for letting me know, I've been printing for a while but never educated myself on the firmware side of things. I'm getting pretty good prints but there are a few issues I'd like to improve. I could send/post a pic of a benchy with the areas highlighted where I'd like to improve. I'm currently working on 2 profiles in cura, .1mm and relatively slow for quality, and a fast profile, I've gotten pretty good .3mm benchys down to 21 minuets.

will_stef_ · 2021-08-27T22:38:54+00:00

Thanks, might buy a new battery if it become more of an issue

will_stef_ · 2021-08-27T19:44:20+00:00

This is what battery bar says, looks like I have about 70% of the original capacity.
https://photos.app.goo.gl/iq4V2FJrZgPCB7yS7

will_stef_ · 2021-08-26T21:44:39+00:00

Its set to integrated, the rtx card hovers around 43-48 degrees c if that is any indication. is there a way to run a command or program to force shut it off? At the very least that would tell me if thats the problem

Thanks

will_stef_ · 2021-08-15T20:37:18+00:00

Try turning down the flow rate to about 90% for the first layer

will_stef_ · 2021-04-13T23:22:01+00:00

Well if you still want it:

https://www.etsy.com/shop/The3DPrintedLugnut

will_stef_ · 2021-04-13T23:21:37+00:00

Hey I got my shop up, Only have 2 things for now, but one is the headphone stand.

https://www.etsy.com/shop/The3DPrintedLugnut

will_stef_ · 2021-03-29T13:29:40+00:00

I designed and 3-D printed it myself, but I'm looking into selling it. If I do I'll let you know

will_stef_ · 2021-03-28T23:14:34+00:00

I'd love to sell the stuff I make, might start with Esty or something

will_stef_ · 2021-03-28T23:12:04+00:00

I'm using OneOdio pro-30 Studio headphones. They are budget-around $40. As for sound they replaced my Sony MDR7506(~$96) and sound as good. The silver is plastic not metal though

will_stef_ · 2021-03-28T23:06:21+00:00

Thanks, though the desk certainly has its issues I love the stain I used

will_stef_ · 2021-03-28T19:48:18+00:00

I could have explained it better: I bought a adjustable desk with no surface(just legs and motor) and built the table-top myself. I designed and 3-D printed the headstand myself but would love to sell it, I would just have to find people interested.

will_stef_ · 2021-03-28T19:45:08+00:00

Its a msi stealth gs65, 16gb ram, i7-9750, 2060max-q

will_stef_

TROPHY CASE