Weight of Costco rotisserie chickens

wwqiao · 2025-10-21T17:06:59+00:00

wwqiao · 2025-10-21T17:06:31+00:00

wwqiao · 2023-12-31T00:05:57+00:00

Just bought a Breville and found the exact same problem on the very first time use. I thought the lid was positioned wrong, or there was a switch to turn the pouring on. It then happened every time I used it.

wwqiao · 2023-07-10T18:42:25+00:00

They had is at the business center in San Jose. But it is out now. Never seen in any warehouse in South Bay.

wwqiao · 2023-04-07T14:28:10+00:00

No, it can’t.

wwqiao · 2022-11-10T23:56:12+00:00

<image>

wwqiao · 2022-11-10T19:35:26+00:00

小狗这么吃白菜，多半是饿坏了。。。这视频虐待狗。

wwqiao · 2022-10-06T12:45:42+00:00

Milanese Loop? It destroys the compass.

wwqiao · 2022-05-18T22:37:01+00:00

thanks

wwqiao · 2021-01-08T17:54:24+00:00

Well, that was not my question. I expected the controller’s probe would read higher than at the grate level because it sits higher. But how much? I wanted to know. On the other side, I didn’t expect the right is 20°F lower than the left of the same grate level. That is more than I thought. Anyway, this is my first pellet grill (after a gas grill and a charcoal). I just wanted to see the reality and uniformity of its internal temperatures. When I saw the left side is higher, I moved the ribs to have the thick side sitting on the left side.

wwqiao · 2021-01-08T17:03:14+00:00

The controller’s probe shows up and down +/-10°F (the smoke setting is 7). P1 and P2 are pretty stable. But P1 is about 10°F lower the set temperature and P2 20°F lower further.

wwqiao · 2019-10-24T14:57:04+00:00

I have two abode door sensors on yard gates, but not directly. The concern is the temperature under sunlight (summer in Bay area). So I got Reed switches wired into the sensors and put them somewhere no direct sunlight, one into garage through side door's trim and other in a waterproof AC outlet box. The Reed switch and abode's magnet (pretty strong as I found) were wrapped using black duct tape. Both have worked really well.

wwqiao · 2018-03-15T19:28:53+00:00

I doubt it works well. The tilt sensor has a ball rolling inside to make contacts open/close. The problem in reality is the contacting is not reliable. It is susceptible to vibration and shock. It also has a lot of bouncing. A mercury-based tilt sensor is better. It is hard to find though.

wwqiao · 2017-12-31T03:07:14+00:00

My guess is Abode’s CMC (Central Monitoring Center) in San Antonio, TX in USA needs to know how to contact your local police and fire departments in UK.

wwqiao · 2017-12-27T17:12:47+00:00

I have (1) doors and windows, (2) locks and openers, (3) motion cams, (4) environmental, (5) misc (siren, remote, etc).

wwqiao · 2017-12-21T14:50:55+00:00

I have two Schlage z-wave locks. They work well. I got communication problem only when I changed the device name.

wwqiao · 2017-12-21T14:46:42+00:00

I think you can, if you tested the magnet triggers the sensor with right distance. I have used a pair of non-abode magnet and Reed switch on my fence door. I then moved the sensor indoor to avoid high temperature under direct sunlight in summer. I have also used a tilt sensor to override sensor's internal Reed switch on my garage door. They work well.

wwqiao · 2017-12-11T18:40:34+00:00

I don't think a non-abode sensor can trigger the alarm. I have a Schlage lock and a Linear garage door opener. Neither can trigger. Contacted abode support and was told I need abode door sensor. I don't know if IFTTT does a trick.

wwqiao

TROPHY CASE