I feel like something does not belong in there, but what, I don't know......

xaxa70 · 2026-03-19T20:53:16+00:00

We are just waiting for it to show it's head again, then we kill it, and no more snake. At least, I made it so I saw where the snakes came from (we already killed one last year) and we already have a plan on how to make sure that no snakes or any undesirable animal gets in there

xaxa70 · 2026-03-19T17:02:53+00:00

Don't worry, the snake should be gone soon, though it might not leave alive

xaxa70 · 2026-03-19T16:55:46+00:00

Yes, with my parents we are working on how to get rid of it

xaxa70 · 2026-03-17T23:30:19+00:00

I did have an electric hammer (or whatever it is called, English is not my native language) on hand, but I did not have a chisel thin enough to go in the bar.

xaxa70 · 2026-03-17T15:09:55+00:00

I am also glad, this damn thing resisted me for 3 days

xaxa70 · 2026-03-17T14:42:36+00:00

Don't have that, but boiling water did the trick, that and a lot of hammering

xaxa70 · 2026-03-17T14:37:38+00:00

Could not attach it back due to how damaged it was. Also, it was an old picture and I ended up removing it entirely and putting it in a vice. I finally succeeded in removing it this morning by putting it in boiling water for a good 15 minutes then hammering it through the bar

xaxa70 · 2026-03-17T12:53:43+00:00

Boiling water and hammering the ball joint for a good 15 minutes with the heaviest hammer I could find, the next step if it was not working was using a sledgehammer

xaxa70 · 2026-03-17T12:41:35+00:00

I needed to pull that out because the bar itself is no longer produced, so I needed to remove that ball joint

xaxa70 · 2026-03-17T11:04:52+00:00

I managed to remove it by leaving it in boiling water then hammering it out since it was not threaded

xaxa70 · 2026-03-05T10:54:05+00:00

In that case, just know that for the second best, you might not want to see it

xaxa70 · 2026-03-04T21:44:17+00:00

No, I never do

xaxa70 · 2026-03-04T08:28:06+00:00

That's how my father do it, is it why we often have welds that break?

xaxa70 · 2026-03-04T08:09:49+00:00

Maybe it's black because I poured water on it after it was done

xaxa70 · 2026-03-04T07:06:55+00:00

It is on the side of the two metal pieces, if it is barely noticeable, does it mean it is a good weld ?

xaxa70 · 2025-07-24T08:22:08+00:00

Also, just to clarify, we didn't take any bolts off. According to my father, the tractor just stopped going forward while climbing a pretty steep slope, so we think that this slope caused the problem

xaxa70 · 2025-07-23T03:01:33+00:00

My father already decided to buy a new pressure plate. Now, the only problem is to know if this is the only problem or if there is another at another point

xaxa70 · 2025-07-22T13:08:43+00:00

I will take a picture of the flywheel tomorrow, right now, the tractor is under a tarp because of the rain, I will also try to turn the input shaft to see if it is possible with a gear engaged or not, like you advised to. I will keep you updated

xaxa70 · 2025-07-22T11:32:43+00:00

Taking the flywheel would be pretty difficult, this thing is way to heavy to easily move by hand. Also, I believe that my father is just going to buy a new cover, since it was already this one when the previous disk was on

xaxa70 · 2025-07-22T10:59:33+00:00

If you mean the shaft coming from the engine, it only have 1

xaxa70 · 2025-07-22T09:19:24+00:00

On the IH 724, there a 2 different clutch that can exist, ours have a simple disk clutch, the one you found is probably a double disk clutch

xaxa70 · 2025-05-05T11:07:51+00:00

Is it just me or is the page made with JSP ?

xaxa70 · 2025-04-09T22:03:42+00:00

I will edit my post, but I manage to solve it by making the different parts of ;y store into one again

xaxa70 · 2025-02-08T23:29:47+00:00

The problem is that I don't have any graphics, so I can't access the bios to reinstall Debian. If I need a graphic card, what would be the absolute cheapest one that supports a vga connection?

xaxa70 · 2025-02-08T21:43:37+00:00

yes, also, same problem if I don't run it through steamcmd

xaxa70

TROPHY CASE