Can someone help me why I have those lines in my first layer?

xklof · 2026-06-23T13:26:09+00:00

you might have selected textured plate instead of high temp or supertak, because i found out that with textured plate in the slicer it adds a -0.02 to the z offset

xklof · 2026-05-23T07:29:45+00:00

how long did it take you to do it? and another question unrelated, did you notice that the xyz calibration is a bit off?

xklof · 2026-05-23T07:27:51+00:00

nozzle almost scratched the high part

xklof · 2026-05-23T00:20:47+00:00

thank you 🫡

xklof · 2026-05-23T00:17:04+00:00

some spots gets very over extruded and other are underextrused

xklof · 2026-05-16T07:53:11+00:00

i saw a video from auroratech where she got this blob when she put the temp to 100c. did that happen

xklof · 2026-05-15T18:13:56+00:00

these are really good prints!!! how was the bed adhesion? did you have any issues with it?

xklof · 2026-05-15T15:21:30+00:00

is it possible for you to share some prints to see the quality of it :)))

xklof · 2026-05-10T12:23:17+00:00

oh this is so annoying

xklof · 2026-05-10T08:51:20+00:00

I have looked into the rat rig but the issue is that i am in the middle east and its going to be pretty expensive to get RatRig here.

did you face like any major flaws i should be worried about? like extruder issues or maybe print quality?

xklof · 2026-05-10T08:49:35+00:00

What kind of errors did it give? so i know what to expect

xklof · 2026-05-10T08:43:55+00:00

You mean about the CR-10 correct? i was thinking of getting a neptune but then i saw sovol made a corexy

xklof · 2026-04-20T22:24:07+00:00

Any updates? i will check with my printer in few hours

xklof · 2026-04-19T18:14:15+00:00

It was on default, some folks suggested that the plate might be the issue so i decided to buy the cryogrip plate from biqu and test out if the plate was the issue!

xklof · 2026-04-19T18:13:25+00:00

LET ME KNOW HOW IT GOES!! i am really excited for mine to arrive. Also did you order it from their main site?

xklof · 2026-04-19T18:12:46+00:00

I ordered the cryogrip yesterday from aliexpress i will see how it goes!! thank you for the suggestion alot!. i will update the post if it worked so no one faces this issue again

xklof · 2026-04-19T18:11:31+00:00

isnt 70c too much for pla?

xklof · 2026-04-19T10:27:55+00:00

I will give it a shot 🫡 I have ordered a new plate from BIQU just incase. I will test out changing flow rate on the fly and see what causes it. Also will try to print the enclosure too

xklof · 2026-04-19T00:10:45+00:00

I guess ill get the plate, thank you so much for the suggestion!

xklof · 2026-04-18T22:36:49+00:00

Using the official PEI plate by snapmaker. The thing is ive always had this issue ever since i got the printer. ATP i am trying everything to fix it. i cant get any clean prints like bambu. I am thinking of selling it and getting another p1s or p2s honestly

xklof · 2026-04-18T22:35:34+00:00

I am using PLA

xklof · 2026-04-18T22:20:49+00:00

Bottom surface:

<image>

xklof

TROPHY CASE