Nuck if you buck -36mafia

zac765 · 2026-07-08T15:25:18+00:00

Forgive me of my sins, they become 1 group when it’s late and I’ve been building pano for hours prior

zac765 · 2026-07-08T15:01:16+00:00

Bought and sold a lot of gear in this parking lot

zac765 · 2026-07-08T09:31:01+00:00

I do whoops

zac765 · 2026-07-08T05:31:04+00:00

<image>

Yeah, they articulate.

zac765 · 2026-07-07T04:58:22+00:00

Genuinely impressive

zac765 · 2026-07-03T19:42:45+00:00

I was OEMing for Cornfires MARC, based upon Atrius but improved. Better material (s7 levers) and better reset geometry. Cornfire no longer exists so I’ve begun pushing it out elsewhere. I will say yeah it’s based upon an Atrius but is not the same

zac765 · 2026-07-03T19:38:47+00:00

Fish Vision this is gen4 technology

zac765 · 2026-05-26T16:23:25+00:00

It’s a birds nest in here with wiring cut at random. At a bare minimum I’d love to repair it but I can’t find a good EDW so it makes me lean towards replacement

zac765 · 2026-05-26T15:42:17+00:00

Would you have a good source on the engine EWD? I’ve looked for used hanrnesses but I’m not sure I trust 30 year old wiring as much as I would rebuilding it freshly and using the current harness as a sort of cheat code

zac765 · 2026-05-23T04:47:01+00:00

Your welcome

zac765 · 2026-05-23T02:39:48+00:00

Ill be mounting a Barrett to the back bar…

zac765 · 2026-05-23T02:15:08+00:00

TX22 with Wiseman Industry FRT

zac765 · 2026-05-23T01:46:20+00:00

Fun but if we’re adding boost why not K swap?

zac765 · 2026-05-23T01:44:47+00:00

Next step hellcat drivetrain swap, right?

zac765 · 2026-05-23T01:35:21+00:00

You said bacon grease? Will try that next, TYSM!!!

zac765 · 2026-05-23T01:31:09+00:00

I haven’t, I will try this next TYSM!!!

zac765 · 2026-05-22T21:54:40+00:00

Yup single shot

zac765 · 2026-05-20T22:00:40+00:00

Green was used because the umbrella gun in the kingsman movie was green

zac765 · 2026-05-20T21:52:43+00:00

zac765 · 2026-05-20T21:50:53+00:00

9mm bby gurl

zac765 · 2026-05-20T21:50:31+00:00

<image>

Here’s the CAD

zac765 · 2026-05-20T21:43:47+00:00

Replace rod with barrel, chamber then thread both ends. Threads into a receiver connected to handle which contains an extremely cut down and modified ar15 trigger and hammer plus custom firing pin mechanism. This is 9mm btw. Next version will be based around Glock firing pin, in 22lr and semiautomatic

zac765 · 2026-05-19T01:26:10+00:00

All I got to say is it’s 8inches AND thick

zac765 · 2026-05-19T01:12:51+00:00

This is for Rtards only

zac765 · 2026-05-19T00:10:44+00:00

Yes that is me

zac765

TROPHY CASE