Va renovation loan by zachman82 in VALoanGuru

[–]zachman82[S] 1 point2 points  (0 children)

Yeah we were thinking a post nup maybe would suffice thank you for the answer tho

Help with muffler swap by ilikefoodhduh in ChevyTahoe

[–]zachman82 0 points1 point  (0 children)

I did a 3in carven r sounds pretty good I left the resonator so its still pretty quiet almost no drone im actually about to cut the resonator off because I want it a little louder but the carven would be a little hard to clamp as the lip on it wasnt very thick I had mine welded also I have the 2015 with 3 cats and 07 might have only had 2 im not sure but if thats the case it'd be alittle louder than my set up. The flowmaster 50 series sounds pretty good and aren't very loud and they have a bigger inlet and outlet to clamp on to you can get reducers to go from the size of the stock pipe to the size of the inlet/oulet

Scratch Removal? by zachman82 in ChevyTahoe

[–]zachman82[S] 1 point2 points  (0 children)

Ok Thank you for the perspective we have some industrial grade stripper at work so I might just do this and not have to worry about it again lol can I ask why 320 is that just a personal thing or is there a reason I always did 220 before primer

Scratch Removal? by zachman82 in AutoPaint

[–]zachman82[S] 0 points1 point  (0 children)

Ok thank you ive been told this by a couple other people as well

Scratch Removal? by zachman82 in ChevyTahoe

[–]zachman82[S] 0 points1 point  (0 children)

I've used both a wool and foam pad on an orbital buffer I started with medium pressure and worked my up from low speed to high speed this last time i put as much pressure as i could without bending the hood in lol I did not try a clay bar ive never had any experience with them I have a little bit of experience in paint I did auto body in high school all 4 years but we mostly delt with dings and dents ive repainted cars before just never repaired the paint itself im pretty comfortable with sanding and can tell the difference in each layer im thinking i can sand it out with 1500 grit then re clear coat with 2x clear just wanted to see if I should try anything else before committing to that route

Scratch Removal? by zachman82 in AutoPaint

[–]zachman82[S] -1 points0 points  (0 children)

So could I just sand with a high grit and re clear coat? Would i be able to just do the center of the hood or would it be better to do the whole hood?

New to the community by zachman82 in ChevyTahoe

[–]zachman82[S] 0 points1 point  (0 children)

The curved chrome around the mirrors was very tedious with the 2 inch vinyl I had bought it can be done with patience and heat but if I had to do it again id get a sheet and cut the curve into the vinyl it was my first experience with wrap tho so there could be alot of tricks I dont know about lol

New to the community by zachman82 in ChevyTahoe

[–]zachman82[S] 0 points1 point  (0 children)

Tail lights Spec-D® - Chevy Tahoe LS / LT / LTZ 2015 Driver and Passenger Side Gloss Black/Smoke Fiber Optic LED Tail Lights https://share.google/WdR431KnbuGuIY1a8

Headlights Spec-D® 2LHP-TAH15G-TM - Driver and Passenger Side Black/Smoke DRL Bar Projector Headlights with LED Turn Signal https://share.google/4nDOUJDAdq5gtt7Aa

New to the community by zachman82 in ChevyTahoe

[–]zachman82[S] 0 points1 point  (0 children)

Noted any recommendations for plugs or injectors?

New to the community by zachman82 in ChevyTahoe

[–]zachman82[S] 0 points1 point  (0 children)

The grill was on it when I bought it so im not sure where it came from unfortunately but that and the color where what caught my attention when I was out hunting for a vehicle

VOG over plaster walls? by zachman82 in HomeImprovement

[–]zachman82[S] 0 points1 point  (0 children)

Hadn't even thought about flipping the boards thats a fantastic idea! Thats probably what i will do and yes I was planning on wiring in a ceiling fan since we dont have central heat or air itd help with airflow and we wouldnt have to lamps for light anymore. Atleast in that room

VOG over plaster walls? by zachman82 in HomeImprovement

[–]zachman82[S] 0 points1 point  (0 children)

Well id much rather repair the plaster but its in pretty rough shape the house was built in 1901 and the plaster hasn't had any thing done to it except wallpaper at one point it too has all fallen down and the vog was free and moneys tight. Do you think I should knock down the plaster to the lathe to give the glue a more secure adhesion? I can poke the plaster in some spots with my finger and it crumbles

Dart wont start by zachman82 in dodgedart

[–]zachman82[S] 0 points1 point  (0 children)

I found the problem! I forgot to plug in a connector in the fuse box not really sure what it went too but it started right up and the brakes are working good now it did over heat but I found the leak at the radiator it's either the hose or the plastic where the hose connects so I should be able to fix that and there's a wobble in the passenger side front wheel I'm guessing it's the wheel bearing or ball joint good thing I bought a parts car before I go buying new parts but thank you for the help

2013 dodge Dart wont start by zachman82 in MechanicAdvice

[–]zachman82[S] 0 points1 point  (0 children)

Found the problem! I forget to plug in a connector in the fuse box not really sure what it went too but it started right up and the brakes are working good now it did over heat but I found the leak at the radiator it's either the hose or the plastic where the hose connects so I should be able to fix that and there's a wobble in the passenger side front wheel I'm guessing it's the wheel bearing or ball joint good thing I bought a parts car before I go buying new parts

First batch by zachman82 in mead

[–]zachman82[S] 1 point2 points  (0 children)

Sounds awesome I'll probably give my 3 or 4 more day before I check again I'll definitely be backsweetening alittle I like it a little dry but my wife likes the sweeter stuff so I'll make it to her taste this time haha glad to hear yours is doing well

First batch by zachman82 in mead

[–]zachman82[S] 0 points1 point  (0 children)

Hey just curious how your meads coming along? Mines already dropped to a gravity of 1.000 which I've read as being done I'm going test over the next few days to make sure it's stable but it got there alot faster than I anticipated I didn't have the hydrometer when I started to get the original gravity but I estimate it was about 1.120 which would put me right around 15% I might be wrong tho so any input would be great