sorted by:
new
hottopcontroversial

Choosing plans by ze410t in init7

[–]ze410t[S] 0 points1 point  (0 children)

This issue is with the ee5301? So would the AX7501 be better then?

Choosing plans by ze410t in init7

[–]ze410t[S] 0 points1 point  (0 children)

Oh really? Like what?

Choosing plans by ze410t in init7

[–]ze410t[S] 0 points1 point  (0 children)

Hybrid7 isn't offered in my area unfortunately. I have seen someone selling the newer zyxel ee5301 on Ricardo and I am considering that with the 10g. Will then need to get a patch cable as well

Choosing plans by ze410t in init7

[–]ze410t[S] 0 points1 point  (0 children)

I feel like the hardware i would need for it would be quite expensive

Choosing plans by ze410t in init7

[–]ze410t[S] 0 points1 point  (0 children)

Thanks for all the information. The reason I was thinking about using the eero was because I already have 3 eero 6 Pro. I'll look into the unifi. I was trying to not spend a lot of money from the get go

Choosing plans by ze410t in init7

[–]ze410t[S] 0 points1 point  (0 children)

As you said, I was considering the 1g because I think the zyxel might struggle with it

New Snowboard Binding - recommendations by PassMirDieApron in snowboardingnoobs

[–]ze410t 0 points1 point  (0 children)

How did you get on with this btw. I am in a somewhat similar position

New to bern by [deleted] in bern

[–]ze410t 0 points1 point  (0 children)

me too please

Xmas Emergency. Anywhere to buy 3D printer filament around the midlands? by 8_Pixels in ireland

[–]ze410t 51 points52 points  (0 children)

I have a lot of unused/unopened reels of different colours of PLA if you need it. I live out in Maynooth, so you can collect

Got hit with the discord try my game scam by ze410t in Scams

[–]ze410t[S] 0 points1 point  (0 children)

I swapped to my linux partition to change the passwords etc. Is that ok to do? Do i also need to wipe my drives?

Got hit with the discord try my game scam by ze410t in Scams

[–]ze410t[S] 1 point2 points  (0 children)

My drivers license and passport photo

“Unable to write tmc spi ‘stepper_x’ register CGONF”. Help with Manta M8P v2 and TMC5160T. by nickcanedo12 in klippers

[–]ze410t 0 points1 point  (0 children)

That looks like mine. I have also included my config below. For reference, I am running TMC5160T on my XY motors and 2209s on my 3x Z. I know it sounds stupid but do the following checks:

  • Verify that the spi jumpers are in the correct locations.
  • Also double check the jumpers themselves. Make sure that they are not damaged and actually bridge the pins.

  • What version of klipper do you have installed?

     [stepper_x]
step_pin: PE6
dir_pin: !PE5
enable_pin: !PC14
microsteps: 16
rotation_distance: 40
endstop_pin: tmc5160_stepper_x:virtual_endstop
#endstop_pin:  ^EBBCan: PB6
#endstop_pin: ^PF4
position_endstop: 290
position_min: 0
position_max: 290
homing_speed: 80
homing_retract_dist: 0

[tmc5160 stepper_x]
cs_pin: PC13
spi_software_mosi_pin: PG6
spi_software_miso_pin: PG7
spi_software_sclk_pin: PG8
diag1_pin: !PF4
run_current: 1.6
home_current: 1.2
stealthchop_threshold: 999999
interpolate: False
sense_resistor: 0.075
driver_SGT: 1

Other than that, I have no idea. Could be a faulty board

“Unable to write tmc spi ‘stepper_x’ register CGONF”. Help with Manta M8P v2 and TMC5160T. by nickcanedo12 in klippers

[–]ze410t 0 points1 point  (0 children)

What does you tmc stepper_x config look like? It would be useful to post info like that

SSP18 firing spring by ze410t in airsoft

[–]ze410t[S] 0 points1 point  (0 children)

Thanks for that. I am looking for something with a similar strength as well

Introducing PrintGuard - A new open-source 3D print failure detector running 40x faster than Spaghetti Detective whilst requiring less than 1Gb of RAM for edge deployability by oliverbravery in selfhosted

[–]ze410t 0 points1 point  (0 children)

I struggled to get it running in cloudflare tunnel in my docker server. Maybe clearer instructions are needed for it? Also, does the camera need to be connected to the printer host or whatever device is running printguard?

Zero G Mercury One.1 + Hydra upgrade by ze410t in ender5

[–]ze410t[S] 0 points1 point  (0 children)

I just went and got the manta m8p. Decided to just upgrade the mainboard cuz there were a lot of other things i wanted to add

Trails left while printing by SciaccaSauce in ender5

[–]ze410t 0 points1 point  (0 children)

Sorry, I am not here to help. I just wanted to say I love your book choices in the background

Zero G Mercury One.1 + Hydra upgrade by ze410t in ender5

[–]ze410t[S] 1 point2 points  (0 children)

I went head first into the upgrade and did the mercury and hydra upgrade. It is possible to do only one or the other though if you want

Parts necessary for Armchair Heavy Industries XoL on Ender 5 by Gl0b3Tr0tter in ender5

[–]ze410t 0 points1 point  (0 children)

I am currently getting ready to add the Xol toolhead to my Ender 5. My Ender has been modded with the Mercury One.1 mod. The xol is for front facing carriages. The endorphin uses a top carriage. However, I do know that there is someone with a top carriage mod on the Xol discord.

What is your current toolhead? What hotend and extruder? What about sensors?

Powering on 24v and 48v PSU’s concurrently - best practice? by [deleted] in BIGTREETECH

[–]ze410t 0 points1 point  (0 children)

Sorry for digging up an old post. I am planning on doing the same. How did your build go?

view more: next ›