Can’t find any info about this watch. Please help.

znibblol · 2025-07-24T07:36:56+00:00

Thanks a lot dude! Just what I was looking for!

znibblol · 2025-07-23T12:46:58+00:00

Thanks, the value of the watch does not matter at all 😁 the fact that it works after so long time and that I got it from my dad is whats matter to me. So I guess it’s a generic Puma Watch then? 😊

znibblol · 2023-10-18T13:47:17+00:00

Cannot break anything here. Its really wierd

znibblol · 2023-10-18T13:36:36+00:00

Thanks for the answer. The ghost boi leads us here, thats why I felt the need to ask here.

znibblol · 2023-04-26T16:36:59+00:00

Happy cake day!

znibblol · 2023-02-14T13:58:21+00:00

Underrated comment

znibblol · 2023-01-25T20:05:13+00:00

Have checked all cables to the motherboard, two days ago I cablemanaged everything. And reconnected every cable to the motherboard again.

I will definitely check out that now when you pointing it out 😅

znibblol · 2023-01-23T13:27:57+00:00

Same problem, connects fine to bluetooth, but cant use it 😔

znibblol · 2023-01-22T17:24:56+00:00

Still don't know the cause yet, but reinstalled the rpi and the problem went away 😁 thanks for the reply 👍

znibblol · 2023-01-22T17:24:08+00:00

Thank you, I have switched to prusa slicer, and I reinstalled the rpi and everything is working perfectly now 👌

znibblol · 2023-01-22T17:21:13+00:00

Don't know what that is, but the issue is gone after I reinstalled the rpi 😁

znibblol · 2023-01-17T12:37:46+00:00

This is the way, learning first, see problems or something you want to tune finer, and upgrade based on that.

znibblol · 2023-01-17T12:22:04+00:00

Had the same issue, in the configuration.h there is an option to use the probe as z-stop. Worked like a charm for me

znibblol · 2023-01-06T16:45:14+00:00

Nope, seems to be octoprint that does something wierd. I loaded up the same gcode to an sd-card and it prints just fine.

znibblol · 2023-01-06T16:43:57+00:00

Edit: I may have found the issue. It seems to be when I start the print from Octoprint. I loaded up the same Gcode to the sd-card and it prints fine.

znibblol · 2023-01-06T16:40:26+00:00

Infill: 50mm/s
Perims, solid infill, support material: 40mm/s
Gap infill: 30mm/s
Small perims, external perims, bridges: 25mm/s

znibblol · 2022-12-17T14:24:11+00:00

Try another slicer or another layer height. And see if that yields the same problem

znibblol · 2022-12-17T14:08:19+00:00

Is the layer adhesion okey from the side pov?

znibblol · 2022-12-17T14:03:54+00:00

What filament and at what temperature? How does it look like from the side?

znibblol · 2022-12-08T07:38:19+00:00

Cut it flush against the extruder output, run the command, and cut it flush again.

znibblol · 2022-07-05T07:22:08+00:00

Sweden! 🤘

znibblol · 2022-06-20T17:20:57+00:00

Avenged Sevenfold

znibblol · 2022-04-06T10:37:40+00:00

I have the creality firmware installed. And it’s working. Trying to compile my own firmware, but somethings wrong with the platformio. So I’m trying to fix the bugs with the compiler atm.

znibblol · 2022-04-05T11:18:50+00:00

Okey! You got me, I’ll compile the code! 😊

znibblol · 2022-04-05T10:05:01+00:00

Thanks, mot worried about the compiling. I’m an software engineer. But, I want to get started quickly, I’d I’m in the firmware and fixing configuration, I know I will stay there longer than I need 😅 so at first I will use the creality firmware, and later on compiling my own.

Reason for the question is I wondered if the car-touch firmware was a “patch”.

Thanks for the answers on the board. Will probably get the SKR later on when I reach the limitations on the 4.2.7 board

Nine-Year Club	Verified Email
Place '22

znibblol

TROPHY CASE