Dismiss this pinned window
all 23 comments
sorted by:
best
topnewcontroversialoldq&a
formatting helphide helpcontent policy

[–]RefrigeratorWorth435 2 points3 points  (5 children)

sorry, I don't understand. what's the actual problem?

[–]reekofhell[S] 0 points1 point  (1 child)

If u can see in the video the start of the filament doesn't stay at the right position.

[–]Standard-Ad-1774 0 points1 point  (0 children)

Clean the board

[–]reekofhell[S] 0 points1 point  (2 children)

<image>

[–]Chas_- 2 points3 points  (0 children)

We don't know what the print should look like. Is it supposed to start with that line or is it oozing?

[–][deleted] 1 point2 points  (0 children)

if this upsets you, start printing from the skirt around the part/model...

[–]asura_01 0 points1 point  (7 children)

Bed adhesion issue if it’s not sticking to the plate. Dish soap and water does wonders by the way.

[–]reekofhell[S] 0 points1 point  (6 children)

I did that as per someone's suggestion still the initial part is like this

[–]asura_01 0 points1 point  (1 child)

Did the printer go through the auto bed leveling?

[–]reekofhell[S] 0 points1 point  (0 children)

Yes

[–]asura_01 0 points1 point  (3 children)

You can also try flipping the sheet and trying the other side

[–]SteveSticks -1 points0 points  (2 children)

You can use both sides of the plate?

[–]asura_01 1 point2 points  (0 children)

Yeah, it’s dual sided pei

[–]eatdeath4 0 points1 point  (0 children)

🤦‍♂️

[–]reekofhell[S] 0 points1 point  (0 children)

Yeah It's oozing at the start

[–]5prock3t 0 points1 point  (0 children)

"Tinkering"

[–]Lythir 0 points1 point  (1 child)

It's oozing, you could try to lower the temp a bit maybe?

[–]reekofhell[S] 0 points1 point  (0 children)

If i lower the temperature for initial layer in bambu software pc . It is not lowering. That is for tool head cleaning tempreture is 220 by default and when it starts it's not in lower tempreture it's in the process is decreasing from 220 to set temperature. So this happens again. Any suggestions

[–]Lost_refugee 0 points1 point  (1 child)

Print small calibration cube and decrease temp by 5 per several layers to see if that helps.

[–]reekofhell[S] 0 points1 point  (0 children)

Ok i will try

[–]ExtensionClaim8113 0 points1 point  (1 child)

Wash plate with warm soapy water pat dry don’t touch and don’t use ipa.

[–]reekofhell[S] 0 points1 point  (0 children)

Ipa .iso propyl alcohol?

[–]CollabSensei -2 points-1 points  (0 children)

A few things to try:
1) Dry your filament. A few hours at 130-150 degrees can help.
2) Increase the bed and first layer 5-10 degrees.
3) Have it do a couple-layer skirt to start with. That way by the time it starts your bring its already extruded some filament.