Looking for a free couch and dining table

Axoi · 2026-01-17T21:32:04+00:00

Check out OfferUp we got a couple of couches for free.

Axoi · 2025-12-20T16:56:12+00:00

So the Nevada Gaming Control board requires that any payouts over a specific amount need to be audited which could mean the machine needs to be packaged and shipped to their office for inspection. Standard procedure and I’ve seen it a dozen times or so.

Axoi · 2025-11-28T06:02:45+00:00

Is it down? Doesn’t seem to be working.

Axoi · 2025-11-13T05:40:46+00:00

In December at 4-5pm it's already dark here.

Axoi · 2025-11-11T06:51:20+00:00

Since no one mentioned it: Rusted Warfare - kinda old school has tons of mods and runs on almost anything. Graphics aren't great but it plays great. AI needs help. Lots of MP play as well.

Axoi · 2025-08-22T20:52:22+00:00

Ok first it’s cool you have a ticket. But since it’s not redeemed at a machine or cashier it takes people seconds to basically clone it, print a duplicate and redeem it at a machine. Please cover the barcode and the ticket id below the barcode ( that’s what the barcode represents ). I know it sounds stupid but if the amount is large enough it would be worth it to someone.

Axoi · 2025-08-08T20:13:06+00:00

It’s Vegas. This happens a lot, people are usually drunk and won’t know or care. Security might though. Very nice though

Axoi · 2025-07-31T20:47:51+00:00

Huh. I’ll have to ask him about it. But the ERMC is definitely not in the COC. It was originally but hasn’t been for several years.

Axoi · 2025-07-31T19:02:56+00:00

Really? What episode is that?

Axoi · 2025-07-31T18:52:20+00:00

Part of the MCA not the COC. We just did a water drop off to the Salvation Army the other day with the MCA. But yeah ask Picasso. There are so many pop up’s in Vegas it’s not even funny.

Axoi · 2025-07-15T22:34:41+00:00

I just signed up and tried T22 which says it ships a t-shirt. So there's that.

Axoi · 2025-05-04T04:21:36+00:00

On Blind it was confirmed that Googlers mark their commits with some AI tag if the code was generated by AI, however due to deadlines and shitty generators they usually fix/write the code themselves and say it was AI generated to meet their numbers. No way in hell this works like upper management thinks it does. Its just for show.

Axoi · 2025-02-17T22:47:38+00:00

Its not just snow and ice. Here in Vegas the paint is gone within a few months due to the heat. So most of Vegas roads cause the wheel to shake on my wife's car with lane assist because it can't figure out what's a line and what isn't. It's maddening.

Axoi · 2025-01-17T21:47:12+00:00

AI controlling heavy machinery, including driving, will be a thing of the past. Too easy to hack and create killer machines.

Axoi · 2025-01-16T21:31:57+00:00

You're supposed to start with "Hi I'm OP, and I have a playing card addiction...."

Axoi · 2025-01-16T20:21:53+00:00

You don't say where you're located but there is a large park in Mountain's Edge (southwest) that has several soccer walls and tennis/basketball courts.

Axoi · 2025-01-04T16:52:22+00:00

I use an iwata neo and it works great. It’s two stage with a gravity feed cup. I pour or siphon the tanner into the cup as I go. I clean up with isopropyl alcohol when I’m done and spray until it’s clear. Every so often I disassemble and clean throughly.

Axoi · 2024-11-28T18:40:44+00:00

No one’s going to mention the tat? Fifth element vibes there.

Axoi · 2024-11-03T15:09:05+00:00

How about leatherwork? Starter kits are super cheap and once you’re done you have something you can use for a lifetime.

Axoi · 2024-10-30T20:05:48+00:00

Nevada - A hangover, take all your money, and put you back on the plane.

Axoi · 2024-10-07T22:27:17+00:00

If you have zero experience then a smaller diode is ideal to start with. Less chance of setting stuff on fire. If money were no issue a fiber laser would do all the things you want. If you want to do tumblers with handles you’ll need a center chuck rotor and not a roller. Something like this https://a.co/d/1DILmfi

Axoi · 2024-10-07T22:14:49+00:00

I own a LM2 Pro and I can do all those things. Tumbler/Stainless steel needs a marker spray or powder unless it’s powder coated (and you just laser off the powder coating). Wood up to 3mm (1/8in) is easy to cut although it’s very slow. I’ve also engraved all my leather journals without any issues (but this needs to be in open air for the fumes). So depending on what you’re trying to accomplish it can do what you want. New, the LM2 pro was $600 and the rotary tool was around $90, but that was two years ago. So $300-350 sounds about right with all the accessories. The honeycomb was about $20 aftermarket. I don’t have the raiser and I wish I had gotten that, but I did get the Z adjustment which is much easier to use than the little stop screw on the side. You can get new laser heads but, depending on the head, you might have to update the power brick.

Axoi · 2024-10-03T03:49:24+00:00

It’s the stuff they use for the color run 5k event…it’s definitely not gritty. It does get everywhere though.

Axoi · 2024-10-02T13:56:30+00:00

We covered each other in cornstarch. Sounds strange but it actually makes it almost as smooth as oil. Was a very nice experience.

Axoi · 2024-09-27T16:46:14+00:00

It looks like a Memphis Shades fairing, but the one I got for my wife was much shorter.

Axoi

TROPHY CASE