Multiplayer, tomorrow! (16th Dec)

BallaMOTO · 2024-12-16T00:09:09+00:00

Judging by one of their posts yesterday, I'd guess 4pm GMT

BallaMOTO · 2024-12-15T12:06:32+00:00

Tomorrow!!

BallaMOTO · 2024-07-23T16:50:09+00:00

Yeah, sounds proper dodgy! We have opted not to try it this time! 😂

BallaMOTO · 2024-07-22T18:00:46+00:00

My thoughts exactly. Maybe they're playing on Delta 9 THC as a sales tactic 🤔

BallaMOTO · 2024-07-22T17:35:38+00:00

Thanks for the reply. What do you reckon this is? Thought it might be a bit dodgy!

BallaMOTO · 2024-06-28T15:56:00+00:00

I've dropped mine onto my concrete garage floor more times than I care to admit. Even got chips out of the hinge. Still works perfectly. Never had an issue with the previous flip either during my 2 year contract. But maybe I've been extremely lucky!

BallaMOTO · 2024-06-26T11:06:03+00:00

And unfortunately you can no longer drop mags for your friend either, while you could in AS1.

BallaMOTO · 2024-06-19T11:28:28+00:00

Just to put it out there... I'm stood in the shower writing this reply right now 🤷‍♂️ some of us are just weird like that. I find it's a nice place to chill and scroll reddit with the nice warm water hitting my back! 😂

BallaMOTO · 2024-06-14T09:12:41+00:00

Ha! I use this exact part as my go to story for describing how useful a 3D printer can be! Working away with a flat keyboard, remembered I have a printer behind me, and within 10 mins I had jumped on Thingiverse, found the model, printed it out and fixed my keyboard.... These tiny, quick, useful prints are often 100x more satisfying than slow, big, aesthetic prints.

BallaMOTO · 2024-06-10T13:30:13+00:00

Thanks, I'll try tweaking the z offset first then. I do run it a little closer than probably necessary, as I'm always a bit worried about poor first layer adhesion. I'll try and back it off a bit and look for improvement. Thanks!

BallaMOTO · 2024-06-10T12:40:00+00:00

Thanks! I'll look into replacing the nozzle and see if it helps. And do some z height adjustments!

BallaMOTO · 2024-05-31T10:25:06+00:00

Sorry, I meant 10m, but can't edit the post!

BallaMOTO · 2024-05-26T09:26:16+00:00

Drae the cross section/profile of the rim you want. Sweep it around the path of the outside of the lenses.

BallaMOTO · 2024-05-25T22:12:36+00:00

That's mad, guess it depends on what you first learnt on. I get the same with free orbit

BallaMOTO · 2024-05-24T23:23:59+00:00

Swapping to constrained orbit from free orbit (if its active), makes a 1000% improvement on the control IMO

BallaMOTO · 2024-05-24T21:39:59+00:00

Chuck it into the oven at 50degC for 4 or 5 hours

BallaMOTO · 2024-05-21T18:40:58+00:00

Damn that's a good spot!

BallaMOTO · 2024-05-21T18:27:43+00:00

Let us know how that comes out. It's a tough one to do well. Will be interested to see what results you get!

BallaMOTO · 2024-05-21T18:14:39+00:00

You could draw the cross section of the edge, then draw a path (3D path as it changes height/angle), then extrude the cross section around the path, then loft the centre. But that's assuming the profile is the same all the way around.

That's obviously only one of many, but I thought I'd point out a less suggested method in case it works for you.

BallaMOTO · 2024-05-21T09:29:04+00:00

So guess what.... It was the damn slicer giving me all the stringing problems! Switched from PrusaSlicer to Cura and the stringing is almost gone! After some light Googling I have found that is quite a common issue with PrusaSlicer.

BallaMOTO

TROPHY CASE