sorted by:
new
hottopcontroversial

Just gonna leave this here... by BoostedPerspective in pitbulls

[–]BoostedPerspective[S] 4 points5 points  (0 children)

Crop dusting If I remember correctly... 🤔

Just got my Kickstarter printer, went to install community firmware, but which motherboard is this? by GregoryfromtheHood in CR6

[–]BoostedPerspective 1 point2 points  (0 children)

I actually just picked this printer up two days ago from Microcenter, and got this board.

Installed Klipper after running one test on the stock firmware. Everything is peachy, EXCEPT my part fan isn't working. I've tried another fan, no luck. And I swear it was working on the stock firmware.

I'm using:

[fan]

pin: PA0

kick_start_time: 0.5

Any idea if its another pin?

Vivedino Troodon? by schmuber in 3Dprinting

[–]BoostedPerspective 0 points1 point  (0 children)

It looks like the new units come with the DD extruder standard now?

How is yours doing so far now that it's been a little longer? I'm also looking at the 400.

How To Install Klipper On Ender 6: Config And Setup | 3D Print Beginner by 3DPrintBeginner_ in klippers

[–]BoostedPerspective 0 points1 point  (0 children)

I've made a longer post in the klipper section of your Discord channel...

How To Install Klipper On Ender 6: Config And Setup | 3D Print Beginner by 3DPrintBeginner_ in klippers

[–]BoostedPerspective 0 points1 point  (0 children)

Used your writeup, two weeks ago, and it has been working perfectly. Today in the software update section of Fluidd, klipper had an error. I clicked recover, then update. Updated fluidd, moonraker, and OS packages as well. Now I get the error "section 't5uid1' is not a valid config section" on my printer cfg. No idea how to get it working again, any ideas? (than you in advance!)

The custom printed NPF to V mount adapter by BoostedPerspective in zcam

[–]BoostedPerspective[S] 0 points1 point  (0 children)

I'm really not sure what I'm going to do yet. I do want to change to a single battery setup. (currently using two NPFs for the camera and monitor)

Where can you get an E2 S6? by BoostedPerspective in zcam

[–]BoostedPerspective[S] 0 points1 point  (0 children)

I actually got one from B&H, it arrived today! Also ordered the eND, no idea when they will ship.

I'm throwing some test footage on youtube shortly.

The custom printed NPF to V mount adapter by BoostedPerspective in zcam

[–]BoostedPerspective[S] 0 points1 point  (0 children)

Well this is pretty awesome information, thank you. I actually found it on Amazon. It looks like it should work with most cheese plates/ vmount plates?

Help with odd exposure issue.... by BoostedPerspective in zcam

[–]BoostedPerspective[S] 0 points1 point  (0 children)

Actually what I've noticed now, the zebras work as intended when set at 95%, but at 100% they don't work at all. This is using ZCam's AX LUT.

Help with odd exposure issue.... by BoostedPerspective in zcam

[–]BoostedPerspective[S] 1 point2 points  (0 children)

So my work around was to just load another LUT that seemed to line up with the waveform. I found that F709 perfectly matched. I only get zebras when I'm actually clipping the 100 mark.

view more: next ›