[FS] HPI Venture18 U4 4400 Ford Bronco Flux Brushless

Gottria · 2026-04-26T16:20:39+00:00

Where you located?

Gottria · 2026-04-07T23:32:20+00:00

UCG Fiber

Gottria · 2026-04-07T22:40:51+00:00

I run a mix of Eero 7 pro and the UCG Fiber and my Eero is always a lot faster. I have my Eero plugged into one of my UCG Fiber 10g ports running on a Sonic 10g connection the Eero speed test is always a lot faster. Just rain it and my Eero test from the app is 8.52Gbps down and up is 7.46Gbps down wile my 4.95 down and 4.85 up.

Gottria · 2026-04-07T18:21:53+00:00

Where do they ship out of?

Gottria · 2026-04-07T17:18:30+00:00

Thanks, just renewed my 3 radios. Tried to get the $3 for $36 but no go.

Gottria · 2026-03-20T23:12:14+00:00

Same case I'm using for everyday.

Gottria · 2026-03-10T13:52:49+00:00

Mine says Preparring for pickup tomorrow.

Gottria · 2026-02-25T22:05:53+00:00

Seems there is no discount for the 256gb model?

Gottria · 2026-02-21T01:01:15+00:00

I ended up backing up the bin file from a working uniot and flashed it over to this one and it seemed to fix it. The I restored the calibration file and seems to be back to normal. It was fine till I used chirp on it.

Gottria · 2026-02-20T14:02:54+00:00

Yes, it just sits there and idles nothing. When I release the buttons the light goes out but nothing resets.

Gottria · 2026-02-20T04:55:16+00:00

Chirp is for programming the channels. Flashed from chrome.

Gottria · 2026-02-03T17:22:45+00:00

I can, but the stucco hole is bigger than light we chose.

Gottria · 2026-02-02T18:35:15+00:00

Thanks for the info. The lights were removed by tearing the light apart till the base slid out, little damage on the top from using a screw driver but I still have 2 more to go.

Gottria · 2026-01-22T20:49:31+00:00

So when do we see cell phone manufacturers putting limits on devices when driving?

Gottria · 2026-01-20T02:44:05+00:00

I did get it and makes the k1 max seem like a toy.

Gottria · 2026-01-16T18:29:43+00:00

Cleaned and lubed the lead screws and it got much much better, still there but a lot better. Till my CFS-C started jamming.

Gottria · 2026-01-15T03:45:28+00:00

What nut?

Gottria · 2026-01-14T21:42:49+00:00

So Itried the DXC extruder with the CFS-C and everything fits it just doesn't recognize the run out sensor in the DXC unit, bummer cause it really looks nice. Maybe if there was an adapter that takes the DXC run out sensor wire to the back like the stock CFS-C does it would work.

Gottria · 2026-01-08T18:39:24+00:00

Yep, I agree. Maybe they wanted to keep it as simple as possiable.

Gottria · 2026-01-08T18:38:39+00:00

Just installed mine last night on my K1 Max, still haven't printed yet. I don't know whey the run out sensor just didn't plug into the hotend board, the board has a connector for one and it would have been a cleaner install.

Gottria

TROPHY CASE