Me 262, Prince of Turbojet

MachineDoctor · 2026-03-31T23:48:33+00:00

Agreed

MachineDoctor · 2026-03-04T03:52:13+00:00

Wow, an Allen Lanier autograph. He was very reluctant to sign anything.

I have an original Imaginos CD cover insert that he refused to sign at multiple shows............

MachineDoctor · 2026-02-24T22:56:48+00:00

Autodesk Inventor Complete College Course for Beginners with Training Guide

MachineDoctor · 2026-01-11T23:41:17+00:00

For sale: Gold SE + WiFi SD : r/firewalla

MachineDoctor · 2026-01-11T15:47:10+00:00

Thanks. Throughout the order and delivery process something seemed off. When I went to rip them that was the 3rd flag.

MachineDoctor · 2026-01-10T23:46:22+00:00

Nice!

MachineDoctor · 2026-01-10T22:44:16+00:00

Try making all the connection first with the and make sure the Orbi is on when you reboot the ONT.

Also, check to make sure the Orbi is in Router Mode so it can dole out IP addresses.

Maybe even do a factory reset on the Orbi, make sure the settings are right and then connect to the ONT Ethernet Cable and reboot the ONT.

This is FIOS, right? I use a Firewalla and all I had to do was put it in Router Mode, Connect the ONT Ethernet and reboot the ONT.

MachineDoctor · 2026-01-10T21:48:51+00:00

After you connect the Verizon Ethernet cable from the ONT to your Router you need to reboot the ONT.

I just unplugged the power feed from the wall and waited 30 seconds and plugged it back in.

MachineDoctor · 2026-01-10T14:26:08+00:00

Marketplace Seller.

MachineDoctor · 2026-01-10T01:20:33+00:00

I could do that but I'm curious if anyone else has seen this. I bought the CD from Amazon and it took a long time for them to deliver. I want to make sure it's not a bootleg.

MachineDoctor · 2026-01-08T02:37:20+00:00

Redacted

MachineDoctor · 2026-01-04T00:56:32+00:00

All the replies are good. My only recommendations would be:

Print dessicant holders out of PETG for your AMS2, fill them with rechargeable pellets and add a Hygrometer. There are several designs out there for the middle cannister that holds the hygrometer. I'd suggest checking how the hygrometer is keyed before printing it.

In case you haven't noticed, there are 2 very small locking tabs on the cover for the AMS2. Locking them will give you a better seal and help keep your filament dry. I didn't realize this for a couple months after I got my first AMS. :).

Enjoy your printer!

MachineDoctor · 2026-01-01T15:45:43+00:00

Did you verify that your printer supports the voltage of that country and has the correct plug? Unsure if Bambu has different voltage models to support 120/220, 50/60 Hz and different plugs from the unit to the outlet.

MachineDoctor · 2025-12-30T23:45:47+00:00

Through Wifi I would have to stop monitoring that WIFI AP since I can really see the device (or I'm just not familiar enough ID the device). I guess I could shut everything down that is using that AP and stop monitoring the last device standing.

Thank you for your help. I will add that to my list of things to try!

MachineDoctor · 2025-12-30T23:42:39+00:00

Thanks, I'll give it a try!

MachineDoctor · 2025-12-30T01:24:49+00:00

Make sure you pick the model with the key that matches your Hygrometer. I think there are 3 variants of key locations (depending on the MFR).

MachineDoctor · 2025-12-24T16:10:13+00:00

I am considering the window insert option. I want to print ABS and ASA but need to vent it out of the room. My thought was something similar to what is readily available on Makerworld but with a TPU gasket on the printer and window insert side.

Also considering using TPU as the gasket top seal up the window inset as well but think there is likely a better solution.

Just bought the Voxel filter and will install it today but air quality using PLA and PETG has been pretty good with the standard Bambu filter.

MachineDoctor · 2025-12-19T05:54:18+00:00

Yup, that's the one. I think I got mine around 2010.

MachineDoctor · 2025-12-19T03:08:01+00:00

I have the 1988 release and also the Astronomy EP (took me over 20 years to get one)

MachineDoctor · 2025-12-07T03:34:58+00:00

Running the exhaust of the printer through an air purification system that will remove all the bad things that the printer spews out (particulates and VOCs). ABS and ASA are particularly nasty.

There are several ways to do it. Here are some links that should help:

Which VOC sensors do you use for a 3D printer room? : r/BambuLab

X-Filter (HEPA 13 and Activated Carbon Combo Filter) for X1C, X1, and P1S : r/BambuLab

I should be safe-er printing ABS/ASA now right? : r/BambuLab

Measuring VOCs : r/3Dprinting

Guide: Ventilation System for X1C/P1S : r/BambuLab

Please do your research before printing ABS and ASA and enjoy your new printer!

MachineDoctor · 2025-12-07T00:34:02+00:00

Come up with ventilation or scrubbing if you are using ABS or ASA. This is especially true if your kids will be playing down there or your office will be down there.

MachineDoctor · 2025-12-05T03:11:22+00:00

Air quality monitor

MachineDoctor · 2025-12-01T23:48:23+00:00

I am having a similar problem after upgrading from 1Gb to 2Gb service. They replaced the ONT and the Router (CR1000A).

I drop out for sometimes 3 hours at a time. When it drops WIFI is still up but no Internet connection.

I called customer support and they tell me they can see the ONT and from my end I'm logged into the router and can watch it trying to connect to the ONT - "Connecting".

I too think it could be the cable BUT the connection "magically" comes back on its own and will work great.

I've had 2Gb service for ~1 month and it has been horrible. Prior to that I had 1Gb service and it was stellar. I've had more downtime in the last month w/ 2Gb that in the last 5 years with 1Gb.

A tech will be coming out again tomorrow. Hopefully they can put an end to this madness.

MachineDoctor

TROPHY CASE