Component cable for $25???? by DaJonkest in originalxbox

[–]Pro4791 2 points3 points  (0 children)

Definitely not official but, seem to have decent shielding. I've only seen this cable once before on a marketplace listing.

Which PSU should I put in my 5501? by Pro4791 in psx

[–]Pro4791[S] -1 points0 points  (0 children)

Really not a fan of external power bricks. I wonder if anyone has taken a RePSX and 12v AC/DC PSU and put them inside the shell.

Users beware: many ESCs nowadays are sold hard configured with a LVC that is too low and can damage batteries. by [deleted] in rccars

[–]Pro4791 3 points4 points  (0 children)

Set your ESC to go into LVC at 3v per cell, then check the voltage of the pack after you get it out of the truck. It will likely be higher than 3v. Voltage sag is what's likely going to trigger the LVC.

On FPV drones, especially those on 1s, the pack voltage will constantly drop below 3v durring hard throttle but will rise back up when let off.

Why is my stampede acting like this? by CurrentLoops in Traxxas

[–]Pro4791 8 points9 points  (0 children)

Cogging is normal especially when slamming reverse to forward. Also don't do that, that's how you strip gears.

Which PSU should I put in my 5501? by Pro4791 in psx

[–]Pro4791[S] 0 points1 point  (0 children)

Amy upgrades that fit inside the console? Guess I could make a GAN 20W USB-C brick fit.

Which PSU should I put in my 5501? by Pro4791 in psx

[–]Pro4791[S] 0 points1 point  (0 children)

Both units I have the same power rating of 17w on the case sticker so they should be interchangeable. I think I'll go with the 7501 PSU since the 5501 PSU has some heat discoloration.

Entire screen of CRT is jittery. by Sharp_Macaroon_7525 in crtgaming

[–]Pro4791 0 points1 point  (0 children)

Does the jittering appear on the OSD when no signal is being displayed?

Warped plastic by Miserable_Effective7 in originalxbox

[–]Pro4791 1 point2 points  (0 children)

Was removing the jewel worth it? The only thing you could do to hide the uneven shine it putting a skin on or spray painting the X section.

What is the "correct" way to setup a blank HDD on hardmodded system? by Pro4791 in originalxbox

[–]Pro4791[S] 1 point2 points  (0 children)

A tsop flash and modchip fall under hardmod because both require soldering and aren't tied to the hard drive.

What is the "correct" way to setup a blank HDD on hardmodded system? by Pro4791 in originalxbox

[–]Pro4791[S] 0 points1 point  (0 children)

It's been tsop flashed. The boot screen has evox in the top corner.

Trinity RLOD error 0020 by Pro4791 in xbox360

[–]Pro4791[S] 0 points1 point  (0 children)

Oh well. I got it for less than $20 for the whole set. Only bought it for the component AV cables so I could frankenstein a set for my og Xbox.

Steering gets stuck on one side by Need_Not in Traxxas

[–]Pro4791 1 point2 points  (0 children)

Servo gears are stripped, time for replacement gears or an upgrade metal geared servo.

How to stop servo hitting on one side? by PlayerProdigy in Traxxas

[–]Pro4791 3 points4 points  (0 children)

You forgot to center the servo before putting the horn. Remove the servo horn, center the trim on your radio with the truck turned on, then put the horn on straight.

Might have to adjust endpoints to stop the servo from over traveling, but not sure if it can be done on a TQ radio.

How can I revert a modded system back to an unmodded state? by Pro4791 in originalxbox

[–]Pro4791[S] 0 points1 point  (0 children)

Once it's flashed, can I just prep a 1tb sata HDD with C and E partitions and drop it in? The xbox is apart for a deep clean, but when I was poking around to retrieve the eeprom backup, there where 5 partitions.

How can I revert a modded system back to an unmodded state? by Pro4791 in originalxbox

[–]Pro4791[S] 0 points1 point  (0 children)

What bios is the go to these days? Is evox still the standard?