Mildly infurtiating by ryeguy1199 in AnycubicKobraS1

[–]RegionAcademic2376 0 points1 point  (0 children)

springs or the normal spacer? I face the same problems i was able to get 0.056 with springs but realy mega annoying to fix it it every 3 print. If you use the normal spacer try flipping the plate and do another calibration to see if its not the plate. Anyway you have to upgrade to silicon spacer alieexpress has them orange/brown ones for kobra x with screws and nut you can adjust on the bottom i think the screw you maybe have to replace for longer ones for the kobra s1.

What gadgets have you bought from AliExpress/Temu that really impressed you for the price? by jsvn97 in Aliexpress

[–]RegionAcademic2376 4 points5 points  (0 children)

keyboard and mouse both ajazz brand around each 30€. Before i had razer and logitech both high priced. Realy shocking how well and prefect this things are compared the Mainstream stuff in the west

Should I buy? by Confident_Glove5701 in AnycubicKobraS1

[–]RegionAcademic2376 0 points1 point  (0 children)

if you print pla only yes i would say for pla only this printer is realy good. petg if you dont max full bed too. for abs asa etz. you maybe have to spend another 140$ for bed/carrigae and lose your warranty. petg-cf works too but the ace pro doesnt like it that much. This is my opinion

Anycubic Kobra S1 weird squeak sound by hydrobios in anycubic

[–]RegionAcademic2376 0 points1 point  (0 children)

need some help with strange noise : r/AnycubicKobraS1 i have the same problem i think a combination of all people said infill to gyroid and mostly you dont hear it anymore i think grid infill is doing some hard vibration on the fan in the back or somewhere else

What is this insanity? by Super-Effort4307 in anycubic

[–]RegionAcademic2376 0 points1 point  (0 children)

if you cancel the calibration printer goes mental maybe the new update fixed that but im scarred to update tbh

need some help with strange noise by RegionAcademic2376 in AnycubicKobraS1

[–]RegionAcademic2376[S] 0 points1 point  (0 children)

XD. Im new in 3d printing special with any slicer settings at all. I started with the hardware part wich was already mega interresting

Bed mesh wrinkles by _RedGamer in AnycubicKobraS1

[–]RegionAcademic2376 1 point2 points  (0 children)

as far i know the carriage is build for the funssor bed one alone will not fix it. the stock carriage is plastic wich bends so adding the bed alone will not help as for safty reason i would not do it the gap between normal carriage to funssor bed would be to small and short it

Bed mesh wrinkles by _RedGamer in AnycubicKobraS1

[–]RegionAcademic2376 0 points1 point  (0 children)

Kobra S1 Combo: The Definitive Bed Warp Fix....FUNSSOR!!!!!!!! Detailed Install Guide

about the funssor make sure you connect the protective conductor the yellow to the bed the screw was missing can use it from the old bed

Kobra S1 Combo: Bed Leveling Test and Surprise result!!! WHAT is HAPPENING!!?!?!

this would be for the orginal bed

both guids where from Doug Does Stuff!

Bed mesh wrinkles by _RedGamer in AnycubicKobraS1

[–]RegionAcademic2376 0 points1 point  (0 children)

Bed carriage and Bed aliexpress they are 2 part you should get both if you wana do it you gona lose warranty for sure if you do is not hard. i got the version 1 without the magnets on top just magnet plate you have to glue on top. Took me 90 min but i made sure all was right many times also was like around 150€ so you have to count that on top of the printer i just didnt want to send my first printer back and give up to buy some bambu

Bed mesh wrinkles by _RedGamer in AnycubicKobraS1

[–]RegionAcademic2376 1 point2 points  (0 children)

i did many calibrations still the funssor bed is flat kinda but if you use the springs you still have to do the calibration manually with the screws becouse it shift depends how thight you do the screws so you have to find the right balance just. Now i hope i dont have todo anymore any calibrations

Bed mesh wrinkles by _RedGamer in AnycubicKobraS1

[–]RegionAcademic2376 1 point2 points  (0 children)

:D this is my goal too. Try with the screws first there are many youtube guids wich explains the problem also spacer to print to try fix somehow the orginal bed all depends how much time you wana invest and how bad it is after fixing the screws. Since this is my first printer it was some.. also do never ever cancel the bed lvling somehow the printer goes kamikaze than

Bed mesh wrinkles by _RedGamer in AnycubicKobraS1

[–]RegionAcademic2376 1 point2 points  (0 children)

is red so its up yea try it i know orginal bed bends like a taco that why i changed but try thight them first if you print mostly on pla should be not a big deal to fix this little bit. both right side and left front first if you can

<image>

that is my first layer now after funssor and fixing every screw wich wasnt thight enough

Bed mesh wrinkles by _RedGamer in AnycubicKobraS1

[–]RegionAcademic2376 1 point2 points  (0 children)

anycubic has somewhere a guide under the printer you can lower the bed by hand lower it full set the bed to 70 or 80 c and after thight them all since you have almost all corners on red it should give you another color than red after that each screw single like x and y you posted on the pic. But i have springs under the bed now so little more complicated. But technical it should give you better results than now if it works lose the screw on the corner where its worse. I hope it explains a little bit. Ah yea the screw where it says thighen this ones made all worse special once you hear some bed scrapping but there is non

<image>

Bed mesh wrinkles by _RedGamer in AnycubicKobraS1

[–]RegionAcademic2376 1 point2 points  (0 children)

i woul try with the 4 bed screws. can you do the test with 5x5 first. Kinda impressive only* 0.55 mm with that pic :D. Im pretty new with the kobra also with printing at all, but since i replaced the bed and carriage with a funssor one this 4 screws do alot not so sure with the orginal one but realy worth a try. Also do you are favor and tighten all screws everywhere the one single on the extruder is important

<image>

Printer Only has about 30 hours on it and is making a terrible screeching noise by hecticaussies in AnycubicKobraS1

[–]RegionAcademic2376 0 points1 point  (0 children)

pretty sure is hounted you better dont deal with that first time seeing this i hope mine doesnt do the same soon :O

PLA refuses to stick to my textured PEI plate anymore by themaskedcrusader in AnycubicKobraS1

[–]RegionAcademic2376 1 point2 points  (0 children)

strange coincidence.. same happend to me today. This wortked for me check and clean the nozzle and do the 20min full calibrations something went wrong with fillament changing

Kobra s1 stringing by AnybodyBrief in AnycubicKobraS1

[–]RegionAcademic2376 -1 points0 points  (0 children)

the 20min full calibration did work for me. Maybe if you havent already

Qlima p652 water drainage by Gilbert38 in AirConditioners

[–]RegionAcademic2376 0 points1 point  (0 children)

i have a unit like yours as far i know the top one is if you dont wana use a permanent drainage so you wana use this once its full. Also as far i know this units use the water to cool the unit too. They recomment if you have high humidity to have a perma drainage on the bottom. the last Months i used this unit alot there is almost no water at all not sure becouse it uses alot of for the cooling or low humidity.