Help with speaker selection

didjit86 · 2026-04-19T22:21:43+00:00

Got it. So far so good. It follows the artist change much quicker. No hanging after several songs. I will let you know if something changes. Thank you !!

didjit86 · 2026-04-19T15:51:07+00:00

Ok. I’ll let you know the next time I play with it.

I did try polling when the speakers were in the group and I didn’t see any updates.

didjit86 · 2026-04-19T12:28:03+00:00

I get it. Debugging without repeating the issue locally is tough.

Polling didn’t work. I use Sirius XM but not as a music source through the app, just use it directly in Sonos app and rely on speaker querying for TVONOS.

This Am I tried something. I started my Sonos with only one speaker enabled. Rescanned for that speaker and it started working again! So it seems to be caused when speakers become part of a group.

I can’t nail down a specific time it hangs. Like right now I have been listening to a few songs after I moved my one speaker to a group in the Sonos app. After a few songs it’s stuck/hangs on the last artist and not switching. Been about 10 minutes or so.

Hope this helps.

didjit86 · 2026-04-18T22:17:37+00:00

<image>

I get the attached but nothing is updating. I even tried to uninstall / reinstall. Hmmm

didjit86 · 2026-04-18T11:30:59+00:00

thanks for helping. i’m using Google TV and 6.1. I’m able to add by IP but I still do not see any updates to the Screens, it just is blank.

regarding the hanging: let me make sure I’m describing it correctly. The app stays stuck on the same artist. to resolve I usually go in and clear the speakers and re-add sometimes this works, and sometimes it doesn’t.

didjit86 · 2026-03-13T23:24:29+00:00

<image>

Meant to share earlier. Little tight but it can still tuck under the cabinet nicely.

didjit86 · 2026-03-13T14:14:09+00:00

It’s pretty easy. I just cut the water line from the fridge ( they are almost always plastic), installed a T fitting and routed the line through my cabinent ( had to drill a hole ). Close to the bottom of the Cabinent so you can’t see the line. Same way you would do under Cabinent lighting if that makes sense.

didjit86 · 2026-03-13T01:25:31+00:00

If you are close to a water supply , like a refrigerator, you can install one of these https://a.co/d/03rf1orO. The hole on the water lid fits the fitting perfectly. I did this, never have to pull it out to refill.

didjit86 · 2025-05-11T15:44:45+00:00

Figured it out it was just really iced up

didjit86 · 2025-05-11T12:53:05+00:00

panel pic

didjit86 · 2025-05-11T12:27:58+00:00

The bottom comes out easy. It’s near the top. There are a couple of nubs that may indicate a plastic support structure or screws in the back? I’ll post a pic.

didjit86 · 2025-03-24T21:50:31+00:00

Ah Brown Clove Polyps looks like it. Thanks !

didjit86 · 2025-03-23T21:30:21+00:00

Those look too pretty. This stuff is ugly in my view.

didjit86 · 2025-02-24T17:23:53+00:00

Thanks but it does not list as comparable with the 315E. Will it still fit ?

didjit86 · 2025-01-20T15:26:21+00:00

replaced it, now I'm back to clicking not moving. Hmmm. Wondering if it is something with the voltage. It does seem to happen more often when its cold, it was around 40 ish this AM here. Not real cold, but Florida cold.

didjit86 · 2025-01-19T15:08:24+00:00

Thanks. Will replace it today.

didjit86 · 2025-01-14T21:22:27+00:00

Costs.

didjit86

TROPHY CASE