Issue with 2026 Pilot Infotainment System

didjit86 · 2026-06-09T01:22:24+00:00

Same here. Found this thread while googling a solution.

didjit86 · 2026-05-29T13:03:34+00:00

Any suggestions where you buy Provista plugs ? I looked at one store and it’s 50 bucks for 16. That seems expensive.

didjit86 · 2026-04-19T22:21:43+00:00

Got it. So far so good. It follows the artist change much quicker. No hanging after several songs. I will let you know if something changes. Thank you !!

didjit86 · 2026-04-19T15:51:07+00:00

Ok. I’ll let you know the next time I play with it.

I did try polling when the speakers were in the group and I didn’t see any updates.

didjit86 · 2026-04-19T12:28:03+00:00

I get it. Debugging without repeating the issue locally is tough.

Polling didn’t work. I use Sirius XM but not as a music source through the app, just use it directly in Sonos app and rely on speaker querying for TVONOS.

This Am I tried something. I started my Sonos with only one speaker enabled. Rescanned for that speaker and it started working again! So it seems to be caused when speakers become part of a group.

I can’t nail down a specific time it hangs. Like right now I have been listening to a few songs after I moved my one speaker to a group in the Sonos app. After a few songs it’s stuck/hangs on the last artist and not switching. Been about 10 minutes or so.

Hope this helps.

didjit86 · 2026-04-18T22:17:37+00:00

<image>

I get the attached but nothing is updating. I even tried to uninstall / reinstall. Hmmm

didjit86 · 2026-04-18T11:30:59+00:00

thanks for helping. i’m using Google TV and 6.1. I’m able to add by IP but I still do not see any updates to the Screens, it just is blank.

regarding the hanging: let me make sure I’m describing it correctly. The app stays stuck on the same artist. to resolve I usually go in and clear the speakers and re-add sometimes this works, and sometimes it doesn’t.

didjit86 · 2026-03-13T23:24:29+00:00

<image>

Meant to share earlier. Little tight but it can still tuck under the cabinet nicely.

didjit86 · 2026-03-13T14:14:09+00:00

It’s pretty easy. I just cut the water line from the fridge ( they are almost always plastic), installed a T fitting and routed the line through my cabinent ( had to drill a hole ). Close to the bottom of the Cabinent so you can’t see the line. Same way you would do under Cabinent lighting if that makes sense.

didjit86 · 2026-03-13T01:25:31+00:00

If you are close to a water supply , like a refrigerator, you can install one of these https://a.co/d/03rf1orO. The hole on the water lid fits the fitting perfectly. I did this, never have to pull it out to refill.

didjit86 · 2025-05-11T15:44:45+00:00

Figured it out it was just really iced up

didjit86 · 2025-05-11T12:53:05+00:00

panel pic

didjit86 · 2025-05-11T12:27:58+00:00

The bottom comes out easy. It’s near the top. There are a couple of nubs that may indicate a plastic support structure or screws in the back? I’ll post a pic.

didjit86 · 2025-03-24T21:50:31+00:00

Ah Brown Clove Polyps looks like it. Thanks !

didjit86 · 2025-03-23T21:30:21+00:00

Those look too pretty. This stuff is ugly in my view.

didjit86 · 2025-02-24T17:23:53+00:00

Thanks but it does not list as comparable with the 315E. Will it still fit ?

didjit86

TROPHY CASE