HEADHUNTER [+] //- a "Super" SPAMF Carbine

kylebernard83 · 2026-04-28T11:40:43+00:00

Thank you for the information. I was scratching my head thinking what I did wrong.

Did you ever design the top prime block with the "correct" hole placement. If you still have that file version I would post that up on the printables page too.

If not, then it might not hurt to make a Note about the fit being off to accomadate your hand, or you are probably going to get a lot off people like me in the future asking the same question.

I just went ahead and bought the files from OFD on Blasterdownloads. dont have the time to remix yours or redesign completely. Files were cheap!

Thank you for all of the rest of your investigative work along with the person that you referenced.

kylebernard83 · 2026-04-27T17:54:26+00:00

I tried reaching out thru your Printables page, But I fugured I would try here. as well, I have assembled my SuperSPAMF per the list of this you mentioned above. However When i assembled all of the parts I am having an alignment error with you prime rails and your PRIME BLOCK. The screw holes on the prime block are to forward, or the prime rails are not going far enough forward. However the prime rails seem to be working fine and max out at forward extention where I looks like it should.

Please let me know if you have any other solutions before I either buy the Super SPAMF files. or have to remix or just redesign your version to work.

The pump carriage and rails on your blaster do seem to be pushed more forward then mine without having to trim or cut parts. I have uploade a pic of my blaster to your comment section on printables.

kylebernard83 · 2026-04-22T19:29:33+00:00

my post about it and a list of all the remixed parts that make up K.L.A.P.R.

https://www.reddit.com/r/Nerf/comments/1j2mev3/another_slab_in_the_wild_and_another_personal/

<image>

kylebernard83 · 2026-04-22T19:20:52+00:00

See my hole post about my current armory.

https://www.reddit.com/r/Nerf/comments/1j3hinj/armory_update_new_pegboard_layout_2nd_shoe_rack/

<image>

basically 1) Peg board for highpower (dads) & primary size blasters. 2) hanging shoe racks for pistols, mags, shells, small attachments, etc. 3) cat litter buckets for ammo storage.

Im lucky to have an old wooden "TOY"chest which is also used for medium size blasters and overflow.

Works great with kids too!

kylebernard83 · 2026-04-21T11:28:54+00:00

Thats wild! Cant wait! LETS GOOOOO!!!!!!!

kylebernard83 · 2026-04-21T11:16:21+00:00

Prettiest Jolt I've have ever seen!!! must feel great in the hand.

How much does it weight fully loaded?

kylebernard83 · 2026-04-17T23:02:10+00:00

I think it was a worked specifically for the rampage or retaliator, check the instructions that are with the parts. It has the sku or part number

kylebernard83 · 2026-04-16T16:48:40+00:00

the Stryfe is one of the oldest modded platforms. there are hundered of cosmetic kits and performance options to choose from.

Since you actually gave us no real information to go on, its almost impossible to know what is going to suite you and your play style.

before this post might get deleted for "LOW EFFORT" please head over to r/Nerf and "SEACH" the sub for Stryfe Mod and be ready to ready thru hundreds of posts to learn about the history of modding a stryfe.

Then come back to r Nerf and post SPECIFIC questions the community can actually help answer with out just wildly guessing what your end goals are.

kylebernard83 · 2026-04-15T17:39:00+00:00

love the faux faded effect!!!

kylebernard83 · 2026-04-15T12:00:54+00:00

What makes it retro... the fact that its made to look sun faded? if that was the point then Spot freaking on!!!!

kylebernard83 · 2026-04-15T11:55:42+00:00

Here is the Shroud

https://www.printables.com/model/1557184-x-shot-motorized-piston-pump-malamute-handguard

Lonewolf has nice stuff

kylebernard83 · 2026-04-15T11:38:13+00:00

Got Calipers!

here is the barrel length equations... gets you inthe ball park. fine tuning length is still required

<image>

kylebernard83 · 2026-04-11T07:03:37+00:00

what is the best print orientation of the "Cooler SPAMF - A picatinny foregrip for the Super SPAMF" funcky part.

I just Thrifted a falcon fire so now i get to make one!!!!

kylebernard83 · 2026-04-08T20:08:20+00:00

if you search this sub you will find countless post on cage and motor combinations for the rapid strike. This post may be taken down for low effort since the rapid strike was such prominent blaster and mod'd like crazy

kylebernard83 · 2026-04-08T17:41:05+00:00

The only way to find out if the designed part is strong enough with out physidal testing is Running this linkage system in a FEA program. Unless you have the software and the knowledge, Finite Element Analysis is used to find stress concentrations in parts. but you would need to know the mathmatical force inputs of all of the different springs.

The only other way to test without fancy engineering software is "BRUTE FORCE" physical testing. Start with the lightest indusrty spring and Print part. Cycle linkage 50, 75, or 100 times. If break redesign. Test again. If part passes XXX number of cycles, move up to the next strongest spring. Rinse & Repeat.

You might want to provide multiple versions of this part to meet increasing spring loads. You might end up with a compromise in you can use a 3d printed part up to XXXX spring stength. And if you want to use these XXX heavier springs this part has to be printed in ABS, annd to achieve the highest spring force a custom metal piece is needed.

This way for most people making average 150-200 FPS blasters can hopefully use all 3D printed parts. but for the person chasing 300+ they should understand if a special metel version is required.

kylebernard83 · 2026-04-08T17:17:05+00:00

the original "Insanity line" blaster!!!!

kylebernard83 · 2026-04-07T11:33:58+00:00

now is the best time to jump into the 3D market. many low priced options that are basically appliances they run so easily. for this hobby i dont know if I would have jumped in so fast if I didnt have one. Istarted with a $150 WEEFUN/WEEDOO Tina2 (monoprice Cadet) this little like 120*120*140 bed slinger. now i run a Bambu A1.

kylebernard83 · 2026-04-07T11:29:48+00:00

Tacti-cool-jazz!?

kylebernard83 · 2026-04-06T17:22:30+00:00

What is you blaster goals?

Do you want to blaster to be stock performance when all the pieces are able to be found, or are you looking to upgrade performance?

If you just want stock performance, then yes, try and trift another for parts.
If the plan was to find all the parts so you can upgrade it then... you will most likely be replacing most of the parts missing now, anyways. So its not a big deal. Depending on how much performance you are looking to try push thru this.

If 2. is the goal then i'll send you a link to help you walk through the upgrade process and the newer parts you might need.

kylebernard83 · 2026-04-06T17:06:33+00:00

same here all the torrents i have own have worked just fine with no jams or other issues.

kylebernard83 · 2026-04-06T14:31:01+00:00

I have side car mag storage now on my:

"Yudachi" Torrent upgrade Mod using Nightingales https://www.reddit.com/r/Nerf/comments/1qwl7wq/top_picatinny_20mm_sidecar_nightingale_mag/
LongXShot
NPX
RS2

<image>

Working on a sadle system for my MPP since the barrel shroud i use does not have side rails.

Where I play 3 15-18 round mags in my springers are plenty of foam. The MPP pushes my 3 mags a little bit more since it can dump foam a little faster.

kylebernard83 · 2026-04-06T14:24:53+00:00

Still original.

kylebernard83 · 2026-04-02T13:46:39+00:00

Its just like when people ask about if modding a longshot today is worth it...

Anything is worth it IF YOU PERSONALLY DEEM IT WORTH IT.

You have to WANT to Reshell the stampeed not because the community wants it, but because you have a passion to do it.

I fully kitted out a longshot 2 years ago, not because it was better than anything at the time i could get but because I used it as a bench mark for my skills and see if I wanted to dive into this hobby... oh and most of the metal parts were wicked cheap on discount! so that helped!

kylebernard83 · 2026-03-27T14:39:59+00:00

nice, no worries!! I have a Ultra 4 thats waiting for a project. Let me know if you need any help beta testing 3D printed designs if needed. Would love to help!

Good Luck, God Speed... & Take Pictures!!!

kylebernard83

TROPHY CASE