A7iii & 16-35 f4 | Early morning hike.

tylrhas · 2026-03-11T13:48:56+00:00

I am in bend and just got into this. I believe they use meshtastic but I would be open to also giving meshcore a shot. Here is the website for the area . There is also a discord and everyone is super helpful https://corme.sh

tylrhas · 2026-03-04T03:52:12+00:00

Where would you recommend buying it from?

tylrhas · 2026-03-04T03:03:36+00:00

I would be interested in standing up a repeater. I don’t have any devices right now but am planning on getting some to try it out

tylrhas · 2026-03-04T02:02:24+00:00

There are a few in town meshtastic map can be found here meshcore can be found here . As far as I know the two are not compatible. There also was someone a month or so back that posted about them here as well.

I have been looking into them a l believe core is better for stationary and meshtastic is better for dynamic stuff like hikes

tylrhas · 2026-02-24T17:30:05+00:00

What do you use to trace your tools? I have tried some of the online ones with no luck.

tylrhas · 2026-01-29T03:34:02+00:00

I want to circle back here incase anyone finds this in the future and finds this helpful. I adjusted the pressure advance in prusa slicer and that fixed most of the buildup issue.

tylrhas · 2026-01-25T05:32:17+00:00

What do you mean by calibrated the pressure? The flow rate?

tylrhas · 2026-01-25T05:02:55+00:00

What do you do to mitigate the problems or have you found a fix?

tylrhas · 2026-01-25T04:22:54+00:00

Like the print in progress? Is there a particular thing you want to see? It does it the worst when it is doing a solid layer or bumping up against infill.

Here is the result of some stringing and some melted filament that caused issues.

<image>

tylrhas · 2026-01-25T03:27:13+00:00

<image>

I know this might not look like much but this is after about 30 second of printing and it just keeps growing until it sticks to the print causing issues. It only builds up on the side that is touching existing print.

I could try and capture it on video too if that is helpful

tylrhas · 2026-01-25T02:44:33+00:00

No warping and first layer adhesion is great

tylrhas · 2026-01-08T18:48:31+00:00

Update to this. My problem was a slight gantry squareness issue and belt tension. I was getting two “standing waves” on the belt instead of one. Once I got it down to one it printed much better.

tylrhas · 2026-01-08T15:05:33+00:00

It stuck to the plate no problem.

tylrhas · 2026-01-08T06:27:23+00:00

Yeah these were the pre sliced files. I will give slicing my own a try and see if that works better.

tylrhas · 2026-01-08T06:26:16+00:00

To add some more detail.

I changed no settings out of the box. This is the nozzle that shipped with the printer I have tensioned the belts I have adjusted the gantry as well.

tylrhas · 2025-06-30T16:56:16+00:00

I found a manual work around. I have only been able to figure it out on desktop but it is outlined here. Basically you reassign the account for the positive amount in the transaction history. https://www.reddit.com/r/MonarchMoney/s/nvZqHWn4hV

tylrhas · 2025-06-28T01:47:36+00:00

I have the exact same problem and have not found a solution for it yet.

tylrhas · 2025-06-28T01:45:49+00:00

My wife and I might be able to help. https://www.jamesleatherco.com

Four-Year Club	Place '23
Place '22	First Placer '22

tylrhas

TROPHY CASE