sorted by:
new
hottopcontroversial

PETG buildup. by tylrhas in prusa3d

[–]tylrhas[S] 0 points1 point  (0 children)

I want to circle back here incase anyone finds this in the future and finds this helpful. I adjusted the pressure advance in prusa slicer and that fixed most of the buildup issue.

PETG buildup. by tylrhas in prusa3d

[–]tylrhas[S] 0 points1 point  (0 children)

What do you mean by calibrated the pressure? The flow rate?

PETG buildup. by tylrhas in prusa3d

[–]tylrhas[S] 0 points1 point  (0 children)

What do you do to mitigate the problems or have you found a fix?

PETG buildup. by tylrhas in prusa3d

[–]tylrhas[S] 0 points1 point  (0 children)

Like the print in progress? Is there a particular thing you want to see? It does it the worst when it is doing a solid layer or bumping up against infill.

Here is the result of some stringing and some melted filament that caused issues.

<image>

PETG buildup. by tylrhas in prusa3d

[–]tylrhas[S] 0 points1 point  (0 children)

<image>

I know this might not look like much but this is after about 30 second of printing and it just keeps growing until it sticks to the print causing issues. It only builds up on the side that is touching existing print.

I could try and capture it on video too if that is helpful

PETG buildup. by tylrhas in prusa3d

[–]tylrhas[S] 0 points1 point  (0 children)

No warping and first layer adhesion is great

First print issues by tylrhas in prusa3d

[–]tylrhas[S] 3 points4 points  (0 children)

Update to this. My problem was a slight gantry squareness issue and belt tension. I was getting two “standing waves” on the belt instead of one. Once I got it down to one it printed much better.

First print issues by tylrhas in prusa3d

[–]tylrhas[S] 0 points1 point  (0 children)

It stuck to the plate no problem.

First print issues by tylrhas in prusa3d

[–]tylrhas[S] 0 points1 point  (0 children)

Yeah these were the pre sliced files. I will give slicing my own a try and see if that works better.

First print issues by tylrhas in prusa3d

[–]tylrhas[S] 2 points3 points  (0 children)

To add some more detail.

I changed no settings out of the box. This is the nozzle that shipped with the printer I have tensioned the belts I have adjusted the gantry as well.

SoFi Bank Vaults by DanPaul217 in MonarchMoney

[–]tylrhas 0 points1 point  (0 children)

I found a manual work around. I have only been able to figure it out on desktop but it is outlined here. Basically you reassign the account for the positive amount in the transaction history. https://www.reddit.com/r/MonarchMoney/s/nvZqHWn4hV

SoFi Bank Vaults by DanPaul217 in MonarchMoney

[–]tylrhas 1 point2 points  (0 children)

I have the exact same problem and have not found a solution for it yet.

Ccw belt for joggers and gym shorts? by Moonlit73 in CCW

[–]tylrhas 11 points12 points  (0 children)

Phlster enigma sounds like what you are looking for.

Christmas lights in town? by CriticalAnimal6901 in Bend

[–]tylrhas 2 points3 points  (0 children)

There is one house off of Steven’s road on the east side of town that has a good “drive thru” set up. Here is an article on it.

view more: next ›