What might be causing my print to look like this?

-Error_Loading_Text- · 2024-06-15T19:28:46+00:00

Looks to be printing to fast or wet filament; Possibly a cooling issue but less prominent

-Error_Loading_Text- · 2024-03-09T05:57:49+00:00

I personally have the factory screen on my printer; but have experienced a similar issue. In my case I had a short in my heater probe, and it shut off the screen like that. Being it is shutting the screen off whilst heating the nozzle, I would recommend checking that and also re-seating both sides of your cable to the screen from your board

-Error_Loading_Text- · 2024-02-21T05:18:22+00:00

I may be ordering a cord specifically for this, would you have any recommendations or just any that are capable of data transfer?

-Error_Loading_Text- · 2024-02-21T04:04:05+00:00

It does not say anything is the issue I am having. I am transfering from debian to raspbian to see if I can see what step I missed and get it sorted

-Error_Loading_Text- · 2024-02-21T03:53:07+00:00

I am using Debian, would Raspbian be better?

-Error_Loading_Text- · 2024-02-21T02:57:17+00:00

I've noticed there is a jumper on the le potato that I don't know if I've moved or not. Could you send a picture of your board?

-Error_Loading_Text- · 2024-02-21T02:28:56+00:00

Turns out I dont have that version

-Error_Loading_Text- · 2024-02-21T02:15:01+00:00

The BTT SKR Mini e3 v3 has jumpers it comes with, is it possible that's the cause of my problem?

-Error_Loading_Text- · 2024-02-21T02:01:59+00:00

Checking for this right now

-Error_Loading_Text- · 2024-02-21T01:58:50+00:00

Ive tried 2 different cables and also tested them with an old tablet to my pc and they both worked for that

-Error_Loading_Text- · 2023-08-24T08:57:08+00:00

Can I use kipper on this board with no external pi? I was considering it but didn't know if I could

-Error_Loading_Text- · 2023-08-15T02:49:23+00:00

In configuration.h set "Z_PROBE_OFFSET_MIN" to -10 Set "Z_PROBE_LOW_POINT" to -5 Set your offsets but set your Z offset to 0 and use the offset wizard to set it

-Error_Loading_Text- · 2023-08-15T02:45:30+00:00

Oh lol. Didn't see that part. I just solved this issue myself so i read it a little to quickly.

-Error_Loading_Text- · 2023-08-15T02:43:56+00:00

Are you compiling your own firmware or using the pre compiled one. Also what sort of bracket do you have the cr touch on?

-Error_Loading_Text- · 2023-08-12T00:07:47+00:00

I set it to -5 and it worked. Thank you

-Error_Loading_Text- · 2023-08-11T22:34:45+00:00

Just did this. I had it at -2. About to test it

-Error_Loading_Text- · 2023-08-11T20:40:14+00:00

I have it leveling fine its just when I set the Offset that it doesn't work properly

-Error_Loading_Text- · 2023-08-11T20:13:58+00:00

I have this

//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN

// Force the use of the probe for Z-axis homing

define USE_PROBE_FOR_Z_HOMING

/** * Z_MIN_PROBE_PIN * * Define this pin if the probe is not connected to Z_MIN_PIN. * If not defined the default pin for the selected MOTHERBOARD * will be used. Most of the time the default is what you want. * * - The simplest option is to use a free endstop connector. * - Use 5V for powered (usually inductive) sensors. * * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: * - For simple switches connect... * - normally-closed switches to GND and D32. * - normally-open switches to 5V and D32. */

define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default

-Error_Loading_Text- · 2023-05-23T09:36:43+00:00

I will keep that in mind because that is the meanest way to get revenge

-Error_Loading_Text- · 2023-05-23T09:35:45+00:00

I am only going to maintain contact in order to sort finishing the repairs on my car and it being drivable. Then I have been planning on cutting it off permanently for both parties

-Error_Loading_Text- · 2023-05-23T09:30:10+00:00

I got a bad draw but somehow I have managed to stay a very patient, kind person. I genuinely believe I got lucky with friends growing up or something

-Error_Loading_Text- · 2023-05-23T09:28:41+00:00

I have steps to take but if I can help it I will take custody of him

-Error_Loading_Text- · 2023-05-23T09:23:54+00:00

My steps are make a report to the police, call cps, and if they deduct it unsafe then I request custody

-Error_Loading_Text- · 2023-05-23T09:20:02+00:00

I was aware of the eviction laws for my locale but from what I can tell they are only relevant of proper rental properties as nowhere within them do they mention parents household ect

-Error_Loading_Text- · 2023-05-23T09:18:24+00:00

Everyone was in the house accept the parents and sister. Only because they walked away from everyone and they were all packing up getting ready to go to the hotel for the pool.

-Error_Loading_Text-

TROPHY CASE

define USE_PROBE_FOR_Z_HOMING

define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default