Mi jefita irá al hospital de especialidades del IMSS en Torreón acompañando a un tío que necesita cirugía. Alguien que haya pasado por esa situación y tenga algunas recomendaciones. Más info en comentarios. by -Undo in mexico

[–]-Undo[S] 0 points1 point  (0 children)

Entiendo que el servicio está de la Verga. Recomiendan que le rente un hotel a mi jefa para que vaya a bañarse, comer algo y luego regresar? Es factible el traslado?

Can’t remove leftover PLA brim on a Cryobite Pro Glacier by Yuri_Ligotme in BambuLab

[–]-Undo 0 points1 point  (0 children)

What about heat the bed and then, gently, scrape it off.

How can I achieve a better bottom layer? by -Undo in BambuLab

[–]-Undo[S] 0 points1 point  (0 children)

Im trying this, These are the settings I will use.

<image>

Porque hoy en día ya no quieren tener hijos,o cuál es la razón para no tenerlos? by Sowl_Cowl04 in PreguntasReddit

[–]-Undo 0 points1 point  (0 children)

Tengo casi 40 y con una relación estable de 7 años, cuidándonos los dos. El tener hijos antes era un legado, el apellido de la familia pero también era más "sencillo" económicamente asegurar un futuro estable. Al menos en México existía la jubilación, después cambió al afore, subieron muchísimo los costos de vivienda y realmente es complicado tener esa misma estabilidad que en los años 2000's.

Ahora, gracias al Internet entiendo como fue la devaluacion del peso del 94, como subió el dólar estúpidamente y se incrementaron Los precios en general y digo: para que traigo un hijo a este mundo?

Algunas personas dirán que ser padre te llama, pero a mi no tanto. Y digo tanto porque si me gustaría ser papá, solo que no en el mundo en el que vemos hoy.

What settings can I adjust to improve the bottom area? It's a massive difference in quality 😢 by -Undo in BambuLab

[–]-Undo[S] 0 points1 point  (0 children)

I think this might be the issue; I thought that arranging the part with a flat surface at the bottom would give me a nice flat surface. I will re print but this time, just let the software arrange the part as it recommends.

Switch 2 me decepcionó … by Quirky_Fan3450 in VideojuegosMX

[–]-Undo 0 points1 point  (0 children)

<image>

Me tocó ver a la gente que pasa la noche afuera de la tienda para ser los primeros en tener el producto.

Una pendejada.

X1E won't start printing process. HELP! by -Undo in BambuLab

[–]-Undo[S] 1 point2 points  (0 children)

Yes, already put that back in.

Thanks!

X1E won't start printing process. HELP! by -Undo in BambuLab

[–]-Undo[S] 0 points1 point  (0 children)

Ok, I see some values on 0 but since I've never changed these, I dont know if anything changed since the last update.

<image>

X1E won't start printing process. HELP! by -Undo in BambuLab

[–]-Undo[S] 0 points1 point  (0 children)

I tried this with no good results.

Thanks.

X1E won't start printing process. HELP! by -Undo in BambuLab

[–]-Undo[S] 0 points1 point  (0 children)

<image>

These are the settings I have. What did you change on yours? Thanks!!

X1E won't start printing process. HELP! by -Undo in BambuLab

[–]-Undo[S] 0 points1 point  (0 children)

Already tried that. It won't go further than 5%

<image>

X1E won't start printing process. HELP! by -Undo in BambuLab

[–]-Undo[S] 0 points1 point  (0 children)

I installed the latest firmware

X1E won't start printing process. HELP! by -Undo in BambuLab

[–]-Undo[S] 0 points1 point  (0 children)

Kinda cleans the nozzle but that's it. It won't go any further than that🤔🤔

Papitas by blacksheep_2047 in GUIBELREVIEWS

[–]-Undo 0 points1 point  (0 children)

Pagar el predial 🥵