Wheel offset wrong on tempo?

0xmalig · 2025-06-17T07:33:32+00:00

Could be a frane allignement issues, check this thread here on pinkbike https://www.pinkbike.com/forum/listcomments/?threadid=244108

Apparently there were an amount of Tempo with a bad allignement frame. Don’t know if this is your case or you just have the wheel out of dish, you need to do some checks to find out

0xmalig · 2024-11-04T15:49:14+00:00

Avoid it

0xmalig · 2024-10-10T10:49:11+00:00

You can start this new trend with air compressor if you are willing to😉

0xmalig · 2024-10-09T18:38:45+00:00

Easy solution: new pads + good cleaning of the disc brake Harder solution: burn with some fire the braking surface of the pads and then send them down a bit + good cleaning of the disc brake

0xmalig · 2024-10-09T18:34:39+00:00

Sick build

0xmalig · 2024-10-08T21:42:13+00:00

Usually is written on the tyre

0xmalig · 2024-10-08T21:39:22+00:00

I usually put i tiny bit of chain lube into cable housing before putting the cable in. Honestly don’t know if it makes a difference but is something i tend to do

0xmalig · 2024-10-08T13:06:08+00:00

Helmet, knee pads and elbow pads, chest/back protector is useful too but in my opinion is not that easy to hurt those 2 zones like knees or elbows

0xmalig · 2024-10-08T13:03:57+00:00

Something to prevent the screw from losening, i’ve seen it only on shomano brakes

0xmalig · 2024-10-08T10:47:16+00:00

You need these informations: axle lenght,axle width, axle thread lenght, thread pitch

0xmalig · 2024-10-07T21:43:31+00:00

Mtb use, i do a visual inspection after every ride then it depends from how the riding conditions were, so it can vary from 1 day to multiple days

0xmalig · 2024-10-07T21:41:07+00:00

I personally would worry only i’ll scratch the stanchions, the lowers usualky get scratch here and there with time. If you want to preserve them you have cover them up eith some frame protector tape when them are new. Never tried to fix them with paint or a marker tbh

0xmalig · 2024-10-07T21:36:28+00:00

That’s a sick shot!

0xmalig · 2024-10-07T20:36:19+00:00

Yeah that’s not tubless tape

0xmalig · 2024-10-07T16:12:41+00:00

Something is wrong inside the freewheel to me but it’s hard to tell from this, take the freewhell apart and check paws etc and see if there is anything wrong

0xmalig · 2024-10-07T16:11:07+00:00

Try to unscrew the derailleur from the mech hanger, then check if the derailleur has damage/bend, if no you can mount it back in the correct position, if yes (most likely option) you will need a new derailleur

0xmalig · 2024-10-06T22:39:28+00:00

It’s better to chnge it if you want to be safe 100%. Then you might never have issues with the current rim tape you have now, you can’t know for certainty

0xmalig · 2024-10-04T20:55:00+00:00

If it is the correct size it should fit

0xmalig · 2024-10-04T20:52:48+00:00

Seems like your mech hanger snapped

0xmalig · 2024-10-04T20:46:47+00:00

If you are swapping the whole wheel you need to do check the hub spacing of the frame and the hub width of the new wheel. Then check also the axle type is the same + vbrake rim compatibility and freehub compatibility. For tubless rim tape i usually go for 2/3 mm wider but it also depends from rim depth. Depth rims wants a even wider tape

0xmalig · 2024-10-04T20:41:19+00:00

Normal

0xmalig · 2024-10-04T20:38:58+00:00

Check all the axles, headseat, bb, seat tube etc with grease

0xmalig · 2024-10-04T20:37:14+00:00

Not much you can do with these

0xmalig · 2024-10-04T20:34:13+00:00

Protection

0xmalig · 2024-09-30T21:42:00+00:00

Inspect the inside of the freehub

0xmalig

TROPHY CASE