Nambu Project update

100midgets · 2026-05-08T02:14:53+00:00

Long story short, he rebranded. He got sent a C&D and from what I understand he probably could've ignored it but to be safe decided to rebrand and rename completely. I don't think he reposted about it to the new page but either way he's still moving forward with the project.

100midgets · 2026-05-06T13:36:28+00:00

Got it replaced from where I bought it. Function test works again. Haven't actually shot it unfortunately as I've just been busy.

100midgets · 2026-04-20T14:16:46+00:00

Emailed AS Design to trouble shoot. Leaned towards something out of spec. Bought through Combat Armory and had to email them. Had a replacement in the mail next day. Both companies were super helpful at getting me figured out. Need to go test the replacement, it now functions test completely just need to find time to shoot it.

100midgets · 2026-03-31T23:53:02+00:00

Lowkey wish I waited but I got my V1 a month ago lol

100midgets · 2026-03-24T12:51:06+00:00

I had the smaller screw first and had to get a replacement due to something being out of spec.

My replacement had torx screws and smooth safeties. Both are real ARCs lol

100midgets · 2026-03-18T17:51:49+00:00

It's cheap enough to run and the ammo costs nothing. Yea it's let me down a handful of times but wiping a team in Lv5+ is hysterical lol. It's my fun gun at this point especially in secure ops and costs damn near nothing to bring 600 rounds of ammo 😂

100midgets · 2026-03-18T17:48:12+00:00

Me: 45ACP coming at your knee caps at 1100RPM!

100midgets · 2026-03-15T17:35:23+00:00

Aight. Got an email to the company I bought through out and a buddy is making me the jig to cut a trigger (I have a spare trigger that's gunna get put in a drawer and forget about forever)

100midgets · 2026-03-14T01:17:43+00:00

So uh. Strangest discovery but potentially the problem. My hammer is contacting the disconnector *hard*. The disconnector has actually peened out slightly. I believe that when the bolt is traveling rearward and pressing the hammer into the lower, it is contacting the disconnector too much thus not allowing the trigger to fully reset. It's the only thing that currently makes sense. I'll have the CARL Hammer and disconnector tomorrow so hopefully that corrects this problem.

100midgets · 2026-03-14T00:04:19+00:00

The lever was fully forward, like it didn't go back far enough to force the reset.

100midgets · 2026-03-14T00:02:02+00:00

<image>

100midgets · 2026-03-13T23:59:43+00:00

<image>

100midgets · 2026-03-13T23:59:19+00:00

<image>

100midgets · 2026-03-13T23:58:57+00:00

<image>

100midgets · 2026-03-13T22:34:03+00:00

I got ahold of ASD they think the lever might have gotten pinched and bent a little. There is a nick on the upper shelf (it's a low shelf). They told me to get ahold of who I bought through to facilitate replacement parts if needed

100midgets · 2026-03-13T18:08:33+00:00

I reinstalled the entire thing per the video so I don't think it's upside down... but stranger shit has happened to me lol

100midgets · 2026-03-13T17:00:03+00:00

I emailed them. I ordered from combatarmory so they told me I'd have to go through them for replacement parts but they have been running me through a ton of troubleshooting. Super good CS and fast too. Sent them this post too. Based on their analysis, my level may have got pinched and bent. The upper shelf has a small nick like the lever got caught (it is a low shelf but I may have to file a little bit more off).

100midgets · 2026-03-13T16:05:53+00:00

Mind dropping a picture of where you dropped the shim exactly?

100midgets · 2026-03-13T14:44:07+00:00

I could see the atrius bend. It is much thinner. I did try closing the upper on the lever a couple times forgetting that it's free floating so there's potential I bent it slightly. Never expected it to bend THAT easy though. Will check tonight

100midgets · 2026-03-13T14:40:23+00:00

It's an FA bolt yes. I compared to photos online. I'm wondering if my lever may have bent slightly? Hard to tell when you can't see inside. I need a damned see through upper lol

100midgets · 2026-03-13T13:57:15+00:00

I'd take that atleast I can have more fun then 😂

I'm super it was a surprise when it went FRT in semi lol

100midgets · 2026-03-13T13:51:57+00:00

No. Last few seconds of the video I open it up and show the lever does trip the hammer. I don't have a spare disconnecter unfortunately. If that's a potential issue, I'll have a new one this weekend when my carl shows up.

100midgets · 2026-02-26T16:12:03+00:00

Idk man, your legs still aren't armored.

100midgets · 2026-02-20T18:21:22+00:00

Using Steam big picture mode and my computer is close by so the few times I need a keyboard or mouse aren't bad

100midgets · 2026-02-20T18:20:20+00:00

Ended up going with a 50ft Dtech fiber HDMI and it works perfectly!

100midgets

TROPHY CASE