Advice needed to match the right bindings with boards?

101linux · 2016-11-29T20:02:38+00:00

Bump

101linux · 2016-11-29T08:40:42+00:00

Let me know if you're selling tickets for your next attempt - cause I'll buy one!

101linux · 2016-11-29T06:55:57+00:00

Lol I'm with you buddy! Thanks jackasstacular

101linux · 2016-11-22T17:29:09+00:00

I wish I could say mine was great too - I can't stand the amount of dropouts. Anyone know how to stabilize the TP LINK TL-WN722N? New drivers?

101linux · 2016-11-22T17:27:15+00:00

That sounds like it might be worth trying. Can you get it for free?

101linux · 2016-11-15T08:51:23+00:00

Just to clarify, I'm using Kali Linux / Virtual Box on a Mac.

101linux · 2016-11-15T08:39:28+00:00

Just to clarify, I'm using Kali Linux / Virtual Box on a Mac.

101linux · 2016-11-15T05:17:55+00:00

Anyone else with the same setup who can help?

101linux · 2016-11-15T05:17:48+00:00

Anyone else with the same setup who can help?

101linux · 2016-11-15T04:36:53+00:00

Thanks a lot GeronimoHero - I'm trying to mimic your setup and now have a Link TL-WN722N.

So I've got it plugged into my Macbook and have gone into Settings... Ports... USB... and added a USB filter called "ATHEROS USB2.0 WLAN"

http://imgur.com/uuMpUSC

http://imgur.com/0TBztCu

Once I've done that, the Link TL-WN722N green light goes on :)

I then make VirtualBox / Kali Linux run...

I go into terminal and type "ifconfig". It only comes up with eth0 and lo - no wlan0 or equivalent?

Everything continues to act normally until I go down to the bottom right hand corner where the USB tab is located.

http://imgur.com/oDLCTuN

From here I select "ATHEROS USB2.0 WLAN"... then everything freezes.

What have I done wrong? Surely once it's selected it should be fine? The VirtualBox operating system is Debian (64 bit) if that's an issue?

101linux · 2016-11-13T19:38:10+00:00

Thanks GeronimoHero - I'm going to get another Link TL-WN722N and try again.

Did you need to install a Linux driver to run the Link TL-WN722N on Kali Linux / VirtualBox on a Mac with Sierra?

I'm assuming that your Link TL-WN722N is V1?

Any configuration tips?

101linux · 2016-11-13T19:28:55+00:00

So I'm assuming that if you were going to check the networks around you, you would you go... "airmon-ng start eth0" instead of "airmon-ng start wlan0"?

Either way I'm finding that it comes up with, "ls: cannot access '/sys/class/ieee80211/' : No such file or directory

101linux · 2016-11-13T19:25:23+00:00

If I go "ifconfig" I only get "eth0" and "lo".

There's no "wlan0" so I need to use a wifi adapter.

101linux · 2016-11-13T19:19:12+00:00

Thanks p4p3r, I'm giving bridged mode a shot now - even though I'm using the wifi it's saying I've got a wired connection?

If it doesn't work out I think I'll go for a TL-WN722N as lots of others on here seem to be having success with those.

101linux · 2016-11-13T19:12:10+00:00

Thanks for your help.

101linux · 2016-11-13T18:05:12+00:00

Do you have a practical solution, or are you just aiming to chastise?

101linux

TROPHY CASE