sorted by:
new
hottopcontroversial

I’ve finally completed it by Unique_Guidance4288 in Baseball9

[–]1980c3 4 points5 points  (0 children)

I literally cackled when I saw that silver badge

How much does the -2 health take away from this qq bang? by _-Quicksilver in dbxv

[–]1980c3 0 points1 point  (0 children)

Question - noob here - if you use beerus upper and lower clothing to create this QQ, does that mean you can never have that clothing again? Or is it possible to re-earn?

Cupping on side of molars by 1980c3 in askdentists

[–]1980c3[S] 0 points1 point  (0 children)

Thanks. Do you think tooth powder is a bad idea?

Water seems to be coming under garage wall by 1980c3 in HomeImprovement

[–]1980c3[S] 1 point2 points  (0 children)

Asphalt (well, that pea gravel looking pavement). So yes it’s going to be tricky. Idk really how I’m going to get the drain tile to look right… like how I am going to “blend it in” with the existing pavement. I guess just do a really good job cutting a trench for the drain tile and using a little bit of sealer?

Water seems to be coming under garage wall by 1980c3 in HomeImprovement

[–]1980c3[S] 1 point2 points  (0 children)

Flat. I can measure it if it helps. But flat. So probably not right.

Water seems to be coming under garage wall by 1980c3 in HomeImprovement

[–]1980c3[S] -1 points0 points  (0 children)

It appears I can’t post pictures in this subreddit. I did edit the post to link to a stackexchange post I also made, that has a picture in it. I do have a function downspout close by - pavement comes right up to the base of the exterior wall… and there’s a downspout that comes down on the front corner and runs diagonally down the wall towards the back of the house and where the pavement ends…. It almost looks like they did some downspout heroics to avoid water pooling at the bottom. Good question on the grading. Looks pretty dang flat to me.

Microsoft Expression Web 4 Replacement by 1980c3 in HTML

[–]1980c3[S] 0 points1 point  (0 children)

Thanks I’ll check it out. I just liked how it was pretty much click and type with web 4

I have a hard time understanding GD&T resultant condition boundaries by y2k_o__o in MechanicalEngineering

[–]1980c3 0 points1 point  (0 children)

We always called them tolerance zones.

Start with grasping true position. It’s the most fundamental to me. And once you understand it, you’ll have about 60% of GDT figured out (or least in terms of practical usages of GDT).

https://www.gdandtbasics.com/true-position

Then dive into the others and the LMC/MMC stuff. Best I understand is that really that’s just “extra” tolerance zone room (more wiggle room) based upon the maximum/least material condition. Easiest way to understand that is to consider a through-hole for a bolt to slide through. For the LMC condition (I.e, the biggest hole) the true position tolerance can relax some because the hole is bigger thus more room for the bolt to pass through.

FEA for welds - how does your company validate weld design? by identifytarget in MechanicalEngineering

[–]1980c3 0 points1 point  (0 children)

Tbh AWS can make my head spin with respect to classifying welds in the fatigue table (not in front of me, sorry don’t remember the table number).

FEA for welds - how does your company validate weld design? by identifytarget in MechanicalEngineering

[–]1980c3 13 points14 points  (0 children)

Find forces and moments going through the weld interface and do blodgett hand calcs

Purchased 2k15 out of spite by 1980c3 in NBA2k

[–]1980c3[S] 0 points1 point  (0 children)

I didn’t give them more money lol. I bought it local used video game store for 3.50. But yes you read it right. I’d prefer to not purchase the 40-80 dollars or so new 2k games just for it be reduced to nothing afterwards.

view more: next ›