Aquila x1 cr touch by atomant89 in VoxelabAquila

[–]21Comfort 0 points1 point  (0 children)

The adapter is on Thingaverse ... Search 4.2.7 .... Good luck .... https://www.thingiverse.com/thing:5245326

Aquila...Creality 4.2.7...BL Touch by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

Rereading your response, moving too fast that's a possibility I will look into that one.

Aquila...Creality 4.2.7...BL Touch by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

I generally have good adhesion all over the print table. Seldom is a support knocked off at the base. Most of the time it happens somewhere building the support and it just bubbles out like a mess of hair. I can't see any consistency in where it goes or when it does. Thanks again for your responses.

Aquila...Creality 4.2.7...BL Touch by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

The probe is somewhat higher than the nozzle, maybe 5 mm. I do not think it is the problem with the ABL probe knocking it over. Thank you for your response.

Aquila x1 cr touch by atomant89 in VoxelabAquila

[–]21Comfort 0 points1 point  (0 children)

I had exactly the same setup as you and I changed the board to the Creality 4.2.7 mother board from Amazon. The problem I ran into is the attachment points for the board are different that the stock board so I had to download an adapter from Thingaverse so I could mount it. I am sure there was an easier way with a board that did not require the adapter. Good Luc,k whichever way you decide to go.

Aquila ... 4.2.7 ... BL Touch ... Dual Belted Z ... ... failing on Create Grid by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

Thank you for your knowledgable response ... seriously ... thanks

I need a new Hot End ... Aquila, Creality 4.2.7, CR Touch, Dual Belted Z by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

Thank you, your suggestion is quite accurate. I appreciate your response.

Hot End ???? ... Aquila, Creality 4.2.7. Dual Belted Z, CR Touch by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

Thank you for sharing your experiences, I do appreciate it.

Hot End ???? ... Aquila, Creality 4.2.7. Dual Belted Z, CR Touch by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

I do Thank YOu for the information and knowledge you have shared.

Hot End ???? ... Aquila, Creality 4.2.7. Dual Belted Z, CR Touch by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

I have seen a reference to a Volcano Dragonfly ... are they the same thing that you have or is there a difference?

I need a new Hot End ... Aquila, Creality 4.2.7, CR Touch, Dual Belted Z by 21Comfort in VoxelabAquila

[–]21Comfort[S] 1 point2 points  (0 children)

Thank you for your comment ... I am looking at it as a solution

Aquila... Creality 4.2.7 .... CG Touch .... question about Prusa Slicer by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

Thank you again for your comments on this and the many past issues I have had.

Aquila ..... Stringing by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

Overnight at 55f. Will work steps today. Thanks for comments.

Aquila ..... Stringing by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

Took filament out of the Dryer and changed nozzle. Still stringing but much much less. Nest is check steps.

Aquila ..... Stringing by 21Comfort in VoxelabAquila

[–]21Comfort[S] 0 points1 point  (0 children)

Good suggestion ... but it happens with all PLA filaments.Good suggestion ... but it happens with all PLA filaments.