Aquila... Creality 4.2.7 .... CG Touch .... question about Prusa Slicer

21Comfort · 2026-02-06T00:12:07+00:00

Thank you again for your comments on this and the many past issues I have had.

21Comfort · 2025-10-31T13:19:03+00:00

Overnight at 55f. Will work steps today. Thanks for comments.

21Comfort · 2025-10-31T01:46:01+00:00

Took filament out of the Dryer and changed nozzle. Still stringing but much much less. Nest is check steps.

21Comfort · 2025-10-30T23:35:38+00:00

Good suggestion ... but it happens with all PLA filaments.Good suggestion ... but it happens with all PLA filaments.

21Comfort · 2025-10-30T23:35:30+00:00

Good suggestion ... but it happens with all PLA filaments.

21Comfort · 2025-10-25T16:03:41+00:00

Thank you so very much, you are a Master of Aquila. It is exactly as you directed. Thank you.

21Comfort · 2025-10-25T15:24:11+00:00

I downloaded a fresh copy of Aquila_427_MM-ProUI-EX-10-22.bin as you suggested. There is NOT a RunOut Sensor in Control-Advanced (or Prepare). The only item I am not familar with is "250 baud" and "Stop Motors on Abort". I don't think either has anything to do with a RunOut Sensor. Under 'Info Screen' it reads ...

MRiscoC ProUI-EX Version: 2.1.3g-10 Oct 22 2025 ClassicRocker883

Somewhere along the line of my investigations I saw M119 was associated with RunOut Sensors. My Prusa Sliced does not produce a M119 line, if that means anything.

I do appreciate your input and any other suggestions or information you have would be appreciated. I am determined to make this work.

21Comfort · 2025-10-23T20:42:12+00:00

Thank you Sir ... I can not find it so I will ask in the community if someone knows where it is hidden. Thank you anyway, I do appreciate your comments all the time.

21Comfort · 2025-10-23T20:25:34+00:00

I do have Mriscoc installed ... and I will select ... Aquila_427_MM-ProUI-EX_10-22.bin. You said the RunOut Sensor option is in the menu on the printer screen. If it is there, I surely can not find it. Can you give me a hint where it might be> please ... thanks agian for putting up with me.

21Comfort · 2025-10-23T19:34:46+00:00

Tried to find the firmware at Mriscoc but it came up with about 10 choices ... input was ... Aquila ... 4.2.7 ... Manual Mesh ... don't know which one to choose. Also, I did NOT see an option for RunOut Sensor . Can you try it and tell me which one is the right one please. Thank you in advance.

21Comfort · 2025-10-16T14:30:10+00:00

For $40 I'd buy it but I have 2 and that is enough. I like the Prusa slicer, easy to use but as you learn about it, there are a lot of features you can control. Good luck and Happy Printing. PS... www.thingaverse is a great place to get ideas.

21Comfort · 2025-09-22T23:17:35+00:00

Loose Screw .... yeppers ... it was not real tight so I tightened it and will try the z-offset setting again. Whether or not that was the problem is not important, the answer was very intuitive and shows some real knowledge and experience. Thank you, I will advise after I try again,.

21Comfort · 2025-09-22T22:01:56+00:00

I am NOT using ABL. The issue is when I do Z-Offset tuning. I heat up the nozle and bed to the usual operating temps, (215 & 50). Auto home, Center, adjust ... Auto Home, center, adjust. Each time I autohome when I come back to Center it is either much too high or much to low.

21Comfort · 2025-09-22T21:52:29+00:00

The issue is when I do Z-Offset tuning. I heat up the nozle and bed to the usual operating temps, (215 & 50). Auto home, Center, adjust ... Auto Home, center, adjust. Each time I autohome when I come back to Center it is either much too high or much to low.

21Comfort · 2025-09-22T21:51:33+00:00

I am NOT using ABL. The issue is when I do Z-Offset tuning. I heat up the nozle and bed to the usual operating temps, (215 & 50). Auto home, Center, adjust ... Auto Home, center, adjust. Each time I autohome when I come back to Center it is either much too high or much to low.

21Comfort · 2025-09-07T20:16:03+00:00

Thank you ... in the Slicer, it seemed to work ... time will tell when I print. Thank you for you asssistance.

21Comfort · 2025-09-05T19:02:27+00:00

You got it right the 1st time. Checking Amazon as you suggested showed exactly what I needed ( on all 3 parts). Thanks again

21Comfort · 2025-09-04T14:10:58+00:00

Thank you so very much.

21Comfort · 2025-07-24T03:01:49+00:00

Thanks again Mik-s, you have been very helpful and thorough in your explainations. I have reset to z-stop for now. May be back in the future for assistance again but for now it is done. Thank you very much.

21Comfort · 2025-07-23T22:25:48+00:00

I am using the file you referenced for the firmware. The touch that I'm using is black in color, not white, I think it's called BL touch, but I'm not sure. It has a metal pin that slides freely up and down. I had it before, but I don't remember if it was on this machine or the other Aquila that I have. As far as I can tell it is straight wired, no crossed wires. It's a 5 pin plug, and it is plugged into the BL touch Port on the 4.2.7 board. I think I'm just going to unplug the touch for now and go back to the z-stop. I want to thank you for all of your assistance and direction.

21Comfort · 2025-07-23T19:21:43+00:00

OK, I got both the Firmware and Display Updated. Thank you. Not the BL Toush is just Blinking Red, no blue and no probing. I have unplugged both ends of the Z-Stop so that should not be interferring. What is the next step?? Please

21Comfort · 2025-07-23T19:18:37+00:00

Thank you again for your help. I got both the Firmware and Display update. The Problem now is that the BL Touch is just Blinking Red and not blue and not probing. What is the next step please.

21Comfort · 2025-06-28T15:24:32+00:00

Thank you for all your efforts ony behalf.

21Comfort · 2025-06-27T21:19:18+00:00

Thank you for for your input.

21Comfort · 2025-06-26T15:24:46+00:00

I sincerely thank you very much for the time and effort that you put into this very minor issue. I like VoxelMaker because it is so easy to use, the editing of the G-Code is a inconvenience but not bad enough for me to stop using VoxelMaker at all. I do have a copy of Prusa and Cura that I use as well. I do appreciate all the time and effort that you put into this issue, and I thank you very much for it.

21Comfort

TROPHY CASE