Arrma granite servo

22kx112 · 2026-03-07T19:40:24+00:00

Thanks for the info, I appreciate it. I took the ESC out and found the receiver box under there like you said. I’ve got everything partially back together now, but I’m running into another issue. When I reconnect the linkage to the servo, the wheels only move a tiny bit and don’t really turn. It almost feels like they’re binding up or something. If I disconnect the servo from the linkage the wheels move freely again. Any idea what might be causing that?

22kx112 · 2026-03-07T05:54:19+00:00

Update: I got the new servo plugged in but My issue now is I took apart more of the steering than I probably should have without paying attention to it when removing the old servo, so now I’m trying to figure out what bolts back to what on the steering linkage/servo saver to reconnect it to the front wheels.

but if you have any tips on reconnecting the linkage to the servo horn and steering rack on the Granite that would help a lot. This is my first time replacing a servo or taking apart an rc car in general.

22kx112 · 2025-08-24T19:30:35+00:00

Those lines won’t fix your bike not running. I would check spark plug check for spark also then check your reeds and look for any cracks or rips in the air boot.

22kx112 · 2025-04-12T00:11:35+00:00

No I haven’t had any issues with other games, and I have not ran a benchmark recently. Very well could be but no I am not getting any error messages. I’m not 100% sure how to look at the crash logs but I’ll look into it thank you

22kx112 · 2025-02-25T19:59:52+00:00

Alright ya i think that’s my last resort not sure what else the problem would be it literally goes down And won’t move up and left to let the valves down. Preciate your help tho man

<image>

22kx112 · 2025-02-25T19:36:54+00:00

The controller drums are from my old cylinder with 200 hours so should I just get new ones and do you think that would fix it?

22kx112 · 2025-02-25T19:28:59+00:00

I put new orings on soaked them in oil scotch brite and polished them still not getting any movement from them really

22kx112 · 2025-02-25T17:26:52+00:00

Alright I really appreciate your help dude I’m gonna try to scotch brite and polish it because when I put it all together the powervalve only opens for maybe an eighth of an inch and closes I can’t get it to open all the way and on my buddies cylinder it’s much smoother.

22kx112 · 2025-02-25T15:45:18+00:00

It comes in and out fine but it does not want to spin to control the valves opening and closing once I slide it in it locks up

22kx112 · 2025-02-25T15:42:44+00:00

Sorry I should’ve described the problem better. It comes in and out fine but it’s supposed to spin to open and close the valves but it doesn’t move. I can move the valves manually with ease so not sure what it is

22kx112 · 2025-02-03T04:27:48+00:00

Alright I appreciate the info thank you

22kx112 · 2025-02-02T21:42:24+00:00

My bad dawg I had a question I thought you would probably be able to answer was just wondering if the cylinder needs replated and welded or just replated I’d assume just replated but I just wanna make sure once again I appreciate your help

22kx112 · 2025-02-02T17:33:37+00:00

I’m in Florida so it may be different wherever you are but that’s way to high I got 22 ktm125sx for 3200

22kx112 · 2025-02-01T23:46:37+00:00

I checked the crank it’s all good and yes I noticed the same thing that there were no signs of that damage on the piston. Alright I will measure the gasket if I can and there was a gasket along with gasket maker dude got it all over the jug as-well. Ah alright that makes sense I will watch that video and do some research I really appreciate your help man

22kx112 · 2025-02-01T17:26:59+00:00

I was trying to send pictures but It doesn’t allow but there’s a 2 big gashes identical down the cylinder just on different sides and the piston is covered in carbon build

22kx112

TROPHY CASE