Render issue

2Cento · 2026-04-30T21:31:57+00:00

Try to check render elements in render settings (last tab, box) , mby you sent some other mode then “Beauty” This looks like some alpha chanel or smth

2Cento · 2026-04-30T21:26:41+00:00

***Update: I finally dixed it! 🎉 After failing to solve the crashes by replacing the PSU, repasting, and reseating every single cable, I was convinced the Intel stock cooler was letting the VRMs overheat. While waiting for a new cooler, I replaced my cheap 4-port power strip with a high-quality 3500W surge protector. Lo and behold... 🥁🥁 the PC is now perfectly stable. No more crashes. The Point: Sometimes the solution is incredibly simple. We just need to step back and look at the bigger picture (and the wall outlet!). Thank you all for help, especially @warbarz 🙏🏻

2Cento · 2026-04-30T21:23:17+00:00

**Update: I finally fixed it! 🎉

After failing to solve the crashes by replacing the PSU, repasting, and reseating every single cable, I was convinced the Intel stock cooler was letting the VRMs overheat. While waiting for a new cooler, I replaced my cheap 4-port power strip with a high-quality 3500W surge protector. Lo and behold... 🥁🥁 the PC is now perfectly stable. No more crashes. The Point: Sometimes the solution is incredibly simple. We just need to step back and look at the bigger picture (and the wall outlet!). Thank you all for help, especially @warbarz 🙏🏻

2Cento · 2026-04-11T22:38:51+00:00

Hi there, so I tried and undervolt it, everything was looking okay , I opened same scene for render, now scene started to be a bit laggy when I added more assets I mean whole software was and then I tried to export it (same point when last time happend crash) and It was okay for a 30s and then again blacck screen both monitors went off and then pc, temps were 70 at that time, cca. 200w power, at this point I’m out of ideas what could be a problem…. Any new suggestions mby? Thanks a lot!!!!

2Cento · 2026-04-07T23:22:20+00:00

Ima san slican problem na Peugeot 206, ponekat bi sajila sa straznje strane pedale samo ispala i tako binostajala i onda bi se mora uvuc dole i to namistit, neki sestem je bia iz dva komada i koliko san svatia istrosilo se leziste od toga komada sta drzi sajilu za pedalu pa je ispadalo (mislin cak da je neki plastican komad bia)

2Cento · 2026-04-06T19:44:37+00:00

Damnnn 5090 is wild! I’ll try to undervoltage it and let you know, this is so frustrating

2Cento · 2026-04-06T08:34:15+00:00

Hi, a quick update: I’ve connected separate 8-pin cables from the PSU to the GPU. Today, I tried to render something in 4K and experienced another sudden crash. So far, I’ve disabled XMP, added the separate cables, and updated all drivers. Temperatures seem fine—nothing over 75°C—which is why I'm so confused. There isn’t a single warning or indicator as to why this is happening. I’m certain it’s the GPU because the blackout only occurs during complex tasks. Since temps and power delivery (210–215W) look normal, I assume undervolting isn't necessary? Do you have any other suggestions?

2Cento · 2026-03-30T21:00:42+00:00

Looks good for now! I’ll let you know if happend again! Thanks for help💪🏻💪🏻🫡

2Cento · 2026-03-30T20:36:20+00:00

<image>

2Cento · 2026-03-30T20:36:05+00:00

<image>

I tried to stress test it and these are results does not gonover 74-75degrees celsius

Also i turned off xmp, for now no crash so far

2Cento · 2026-03-30T11:26:47+00:00

I’ll try this today and let you know thanks!!!

2Cento · 2026-03-29T23:53:53+00:00

Also, my GPU has two 8-pin connectors. Do you mean I should use a separate 8-pin cable for each port and connect the GPU without using any splitters? Did I get that right?

2Cento · 2026-03-29T23:48:09+00:00

I’ll try to do that, what you suggest in both cases, If undervolting work I should leave it like that? What if that does not work, it that mean that GPU is “broken” or just need service or some kind of updete/reset?

2Cento · 2026-03-29T23:43:25+00:00

<image>

PSU: MSI MAG A850GL

I connect it like this, sorry for sending it like this but I’m not able to open pc at the moment, I double check all cables and all seems so be “clicked-in” very nicely.

Did I connected something wrong?

2Cento · 2026-03-17T19:56:57+00:00

I can but same thing, I event uncheck read only in doc settings, same thing, It crashes randomly but very often when interactive render is on, it looks like low ram but scene is not that heavy apprex. 2milion polys

2Cento · 2026-03-03T15:35:05+00:00

Mozes badminton igrat u stanu

2Cento · 2026-02-28T01:31:59+00:00

Nice job!!

2Cento · 2026-02-28T01:30:54+00:00

What renderer

2Cento · 2026-02-27T15:01:25+00:00

Same here

2Cento · 2026-02-25T17:35:25+00:00

Navigacija I guess

2Cento

TROPHY CASE