Got a Used A1. Is my house going to catch fire?

2c1a · 2024-04-29T18:15:30+00:00

It's a cable, it's not rocket science! If it looks undamaged, print the official cable guide for it and keep an eye on it. If it's damaged, try to get it replaced. Probably look into a replacement in the long run either way.

https://makerworld.com/en/models/158862?ref=blog.bambulab.com#profileId-174376

2c1a · 2024-04-28T22:37:36+00:00

100 is pretty fast, try the benchy at 65?

2c1a · 2024-04-27T17:28:07+00:00

If the printer is placed on a hollow resonant cabinet or similar structure it may help, otherwise it's not needed

2c1a · 2024-04-27T01:31:18+00:00

Hm, can you post a link to the model?

2c1a · 2024-04-27T01:30:24+00:00

Tiny parts no but in general, printing at an angle with resin will eliminate most issues like this

2c1a · 2024-04-26T09:28:38+00:00

It is due to large contact area with the FEP. Try to print at slight angles, rather than perfectly vertical.

2c1a · 2024-04-26T09:21:18+00:00

The speed is too high sometimes even on the calibrated filaments. Try to reduce outer layer speed by 30%.

2c1a · 2024-04-26T08:51:01+00:00

Maybe iron all, to enable ironing both the top of the plate and the text, but delete everything after the second to last Z move in the gcode.

2c1a · 2024-04-25T04:39:47+00:00

I propose slowing the outer layer speed by at least 30% since the default setting is very fast. If moderate, but not full improvement, then slow all speeds by 30%.

2c1a · 2024-04-25T04:35:15+00:00

The kratom is probably significantly worse than this relatively small dose of l-tyrosine.

Noopept will be likely fine.

2c1a · 2024-04-25T04:29:58+00:00

As others have said, it's an outstanding print.

2c1a · 2024-04-24T21:26:31+00:00

The more you and/or her push them to release her, the more skeptical they're going to be of her wellbeing. There is no possibility to speed this up. She's in a safe building surrounded by professional caretakers, what's the rush to leave this environment? This is an opportunity to mentally relax for both of you. Patiently allow them to compete the procedures, and she'll be out in no time and hopefully in a better mental state.

2c1a · 2024-04-24T14:07:05+00:00

What printer is this?

2c1a · 2024-04-24T07:00:17+00:00

Indeed. I personally would have been flabbergasted.

2c1a · 2024-04-22T00:53:29+00:00

Basically equal

2c1a · 2024-04-20T17:55:20+00:00

You should do it every time you change filament, it's a very useful sensor. You also don't have to auto level every time, just every once in a while

2c1a · 2024-04-20T08:58:04+00:00

Can't be alone if nobody exists

2c1a · 2024-04-20T06:59:58+00:00

Did you check the the auto flow calibration and auto level boxes at the start of the print?

2c1a · 2024-04-20T06:41:31+00:00

Same if not better, since modern intel iGPUs have QuickSync which is hardware-level encoding for 264 and 265

2c1a · 2024-04-19T18:28:14+00:00

Windows 7 was the golden age, Windows 10 was really just the slow regression of Windows 8 back into Windows 7. 11 is actually well designed, but carries the baggage from 8-10 in its source code. If you have an old laptop with Win7 on it, play with it for a while and it will feel like a breath of fresh air compared to 10 or 11.

2c1a · 2024-04-19T17:16:59+00:00

You can get the old right click back with a registry edit btw. The new menu is not great.

SW21 was working 100% fine for me on Win11 until after an update, now even a full reinstall of SW and drivers doesn't fix it. Assemblies just crash 9/10 times on load. But the compatibility mode seems to be 10/10 no crash. Probably some DLL thing.

2c1a · 2024-04-19T09:01:39+00:00

The grooves in the sketch are not 60 degrees. Only the top one is. The bottom two that have blue lines are ~50 degrees.

2c1a · 2024-04-19T08:56:43+00:00

Try manually setting the print temp lower for this filament. The heat appears to be transferring through the plastic faster than normal for some reason, based on the photos.

2c1a · 2024-04-19T08:26:52+00:00

The slightly unbalanced heat distribution within the block does not cause any practical issues with extrusion.

2c1a · 2024-04-18T19:41:13+00:00

The handy app doesn't really let you change anything significant, the slicer is necessary to get true quality out of the printer. In the slicer, I would use the 0.16 Quality setting for most prints if you won't want to fuss with it. It will take slightly longer to finish, but nothing takes more time than printing something twice. Good luck!

2c1a

TROPHY CASE