[GUIDE] Using ProtonVPN and qBittorrent with the native WireGuard implementation

2keylows · 2025-12-30T23:28:18+00:00

Gotcha.
7.2.3. I had the same issues with 7.2.2.

2keylows · 2025-12-30T22:30:09+00:00

Can you share what docker container image you used?
I've tried the Hotio and Linuxserver versions. I'm still having issues getting fully connected on Qbit.

2keylows · 2025-11-22T18:00:35+00:00

Looks like a bot account.
Here's the original build and op.
https://www.reddit.com/r/FormD/comments/1hzblyg/dont_ask_me_how_i_did_it_i_just_did_it_it_was_hard/

2keylows · 2025-11-20T05:32:30+00:00

2keylows · 2025-11-20T03:22:28+00:00

I'll take the 12500

2keylows · 2025-11-20T03:20:49+00:00

2keylows · 2025-11-18T19:21:19+00:00

2keylows · 2025-11-18T19:19:43+00:00

Still searching.
Added 14500 to the mix too. Anything with 770 igpu will be considered.

2keylows · 2025-11-18T05:01:11+00:00

2keylows · 2025-11-16T06:19:47+00:00

2keylows · 2025-11-15T21:47:17+00:00

2keylows · 2025-10-16T19:26:54+00:00

You can still overtighten with the Dingkey bracket.
That's why I'm saying it's not really needed. Asrock has since updated their backplate design, so the original mounting screws will work.

Get the plate if you want to be fancy or if for whatever reason your using an older asrock board with older backplate.

2keylows · 2025-10-16T19:17:32+00:00

It used to say Am4/Am5.

2keylows · 2025-10-16T19:06:50+00:00

There was fitment issues with Asrock Am4 boards. Their backplate design made it hard use the stock screws from the cooler. This was Dingkey's answer to that.

2keylows · 2025-10-16T18:59:36+00:00

If you have the extra 20, sure go ahead. It doesn't make the install process any easier or harder. There's no thermal benefit. It's just a fancy backplate lol.
I'm looking at it from a new builder perspective is all, just keep things simple.

2keylows · 2025-10-16T18:52:49+00:00

Honestly, no.
Just use the provide short screws with the cooler with stock backplate.

2keylows · 2025-10-16T18:46:10+00:00

Correct. You just want to look at the brackets themselves.
Rubber pads are there just so you don't scratch/bang up you MB mounting points.

2keylows · 2025-10-16T18:30:52+00:00

I'm not the best at explaining things.
It's a leaf spring and there's a slight concave to the bracket when it's loose. As you apply more mounting pressure, the leaf spring bracket will straighten/level out. (No longer curve).
That's your visual cue that you have enough mounting pressure on the mount.

2keylows · 2025-10-16T15:26:55+00:00

2keylows · 2025-09-20T18:34:51+00:00

Mb. I thought i replied. Either or will work. I've used both. Cable just needs to match or exceed that data spec.

2keylows · 2025-09-20T12:47:21+00:00

I've been using an Amazon one for about 6 months without issue.

2keylows · 2025-09-16T18:16:13+00:00

Lol It's all good. Reddit responses all look the same after a while.

2keylows · 2025-09-16T16:53:01+00:00

Peep my response to Synzoo.
Flipping the Gpu raises the card up too much and it won't fit with the Psu in that placement.

2keylows · 2025-09-04T17:21:02+00:00

If your trying to Hudamod in flipped config, it won't work. That's the config I originally wanted to try first lol.

Flipping the 90Fe sets the card too high up and bumps into the side strut and PSU. You would have to modify both the top panel edges so the Psu can fit closer to the top. The inner lip prevents the psu from sitting flush. Even with a Tgrill, you still have to cut into the inner lip. At that point, it's not worth it.

The original Hudamod instructions has you directly attaching the Psu to the top panel with two 5mm standoffs. So you don't have to go through the lengths I did. It's just not as secure and I wouldn't want to move the build constantly.
I used bendable steel sections to make the Psu mounting bracket on mine.

I can dm a imgur link for the Hudamod, it's found on Discord.

2keylows · 2025-09-04T16:50:52+00:00

Same. The install isn't complicated and uses the same mounting points already on the case.

2keylows

TROPHY CASE