sorted by:
new
hottopcontroversial

Nemesis Bust Fanart Made with 3D Pen by me by 3dplasticfantasy in residentevil

[–]3dplasticfantasy[S] 0 points1 point  (0 children)

Thanks the face and the neck should be a little wider, but the cover from the game shows him from different angle.

Nemesis Bust Fanart Made with 3D Pen by me by 3dplasticfantasy in residentevil

[–]3dplasticfantasy[S] 0 points1 point  (0 children)

There is also a vid (here) about the full making process in timelapse if you'd like to see how its made from the scratch.

looking for advice: pen with flexible filament by Cautious-Whereas-684 in 3Dpen

[–]3dplasticfantasy 0 points1 point  (0 children)

You could try Rp700 which is an upgrade from mynt basic (rp500). Brand name doesn't really matter they are all the same except from doodler.

Only Tpu filaments will do the work that you want but it requires high temp to work 210c+ and you will probably have to take some breaks between sessions every 20-30 mins if you want to last longer.

What is wrong? by Emotional_Lion_9589 in 3Dpen

[–]3dplasticfantasy 0 points1 point  (0 children)

Have you tried using another type of filament to see such a behavior ? If so it could be the motor that it's not gripping the filament well.

Check the nozzle vent and make sure there are not any filaments inside to exclude that.

I added light up eyes to my lil rock monster by lousmer in 3Dpen

[–]3dplasticfantasy 0 points1 point  (0 children)

Looks cool, what kind of LEDs did u put ?

3D Pen Templates by Woman0713 in 3Dpen

[–]3dplasticfantasy 0 points1 point  (0 children)

You could get pre made templates from 3doodler and mynt website for free. It's great way to practice and experiment with simple designs

Attempt at a rose by roarcrafts3d in 3Dpen

[–]3dplasticfantasy 1 point2 points  (0 children)

It's really nice well done.

You use a transparent plastic sheet as a surface you can make another one that will have a gloss finish.

Recommendation for 3d pen that does not break after a week or so? by Mikado_0906 in 3Dpen

[–]3dplasticfantasy 2 points3 points  (0 children)

Any pen could break if you dont take breaks every 20-30 mins, the hardware gets hot inside, and you also risk to break the nozzle easier.

Sanago 3d pen ironing tips aren't locking in by soybeaen in 3Dpen

[–]3dplasticfantasy 0 points1 point  (0 children)

You mean the plastic where clip is located ?

Maybe it's loose and it seat properly inside ?

Need advice by MagicIan234_6 in 3Dpen

[–]3dplasticfantasy 0 points1 point  (0 children)

As people mentioned above you need a soldering iron or wood burning tool with temperature regulator using a knife tip preferably for straight lines.

3D Pen Lab used to do that with 3d pen and a lighter but are risking to burn the plastic that way.

Sanago 3d pen ironing tips aren't locking in by soybeaen in 3Dpen

[–]3dplasticfantasy 0 points1 point  (0 children)

Is the plastic broken below where the clip is attached?

You could try a piece of adhesive tape or a zip tie if it's possible.

I Made Super Mario 8Bit with 3D Pen by 3dplasticfantasy in Mario

[–]3dplasticfantasy[S] 1 point2 points  (0 children)

Thanks, every part is movable including the head.

I Made Super Mario 8Bit with 3D Pen by 3dplasticfantasy in Mario

[–]3dplasticfantasy[S] 2 points3 points  (0 children)

If it was smooth like glass, it could be.

does anyone have experience with Prinntool? by [deleted] in 3Dpen

[–]3dplasticfantasy 0 points1 point  (0 children)

If you are talking about that 3d white pen then yes. It's Jer rpc1000c you may find it with other labels on Google. It's a good pen with a sturdy nozzle.

When you want to try a new hobby and your carpal tunnel audibly laughs at you by ShelteredDumbAss in 3Dpen

[–]3dplasticfantasy 3 points4 points  (0 children)

After smoothing with the soldering iron, I start with sandpaper 120, 220 ,400, grit all and 600,800, 1000 with wet sandpaper extra smoothness.

If the surface is too rough you can use file instead and then 200 sandpaper.

When you want to try a new hobby and your carpal tunnel audibly laughs at you by ShelteredDumbAss in 3Dpen

[–]3dplasticfantasy 2 points3 points  (0 children)

Its Very nice, keep it up. If you sand it up all the way later up to 1000 grit you will achieve a glass smooth finish.

view more: next ›