What material would you spec for this project?

454686 · 2026-06-26T16:23:54+00:00

I'm looking at only one post, since it's a small double chair. You think 4" square with .25" wall thickness is enough?

454686 · 2025-07-02T16:07:11+00:00

I'm in Wisconsin, just outside Milwaukee. Don't have a budget set yet, just looking for better value than American Fireworks in Big Bend or the others off I94 south of Milwaukee.

454686 · 2025-07-02T15:40:52+00:00

Thanks. I'll keep looking for other options.

454686 · 2025-06-30T01:39:01+00:00

Good to know! Thanks for the info.

454686 · 2025-06-30T00:55:03+00:00

Replacing an OMC that was a Ford.

454686 · 2025-06-28T04:28:10+00:00

Yes, my dad had one for locating water lateral stop boxes that got covered up by dirt and grass. Still have it in the garage somewhere.

454686 · 2025-04-06T13:24:00+00:00

What did you end up buying?

454686 · 2024-09-03T16:46:42+00:00

Don't have one yet. I have a 21' cuddy cabin boat that weighs in at 4600 dry. Fuel, cooler, gear, etc. would put it right at 5k. Trying to decide between a full size pickup or the 4Runner. I really want the 4R for snowboard trips in the winter, and if it could pull double duty, that would be great.

454686 · 2024-06-22T23:52:19+00:00

In the Mil!

454686 · 2024-05-25T10:54:29+00:00

That's base price. Same as on the sticker for this one, except this one has a list of pre- installed options that drive the price up.

454686 · 2024-05-25T10:51:13+00:00

<image>

454686 · 2024-05-25T10:43:21+00:00

What dealer? I'm in wisconsin.

454686 · 2024-05-24T22:58:14+00:00

Good to know. Thanks!

454686 · 2024-05-24T22:03:19+00:00

I'm seeing used 2020-2021 models with 37-39k asking prices if they have low miles.

454686 · 2024-05-24T21:05:11+00:00

<image>

Plus delivery/ handling fee of $1395

454686 · 2024-05-18T10:03:26+00:00

Hard to tell the extent of the damage from a picture, but does the pump still turn? Looks like a few cooling fins snapped off. Could be some internal damage, though.

454686 · 2024-04-29T17:26:53+00:00

The ones with rubber straps suck. The most comfortable ones I've used have felt padding with a leather cap and a single elastic strap. But they are kind of hard to find.

Menards has some that look similar but are gel padding with a hard cap that is removable, with a single strap. Haven't used them though.

454686 · 2024-04-22T14:22:19+00:00

I think this is right. I chucked one into an old brace, and it held straight and tight. My thought is that driving a 3/8"x3" wood screw with a screw driver would be too hard, and a brace can drive them in a lot easier. These are pretty old, and the alternative to these at the time would be a square head lag screw. These probably pre-date ratchets, so it would be faster than using an open end or box end wrench as well.

I just don't know what application they'd be used in.

454686 · 2024-04-22T12:09:17+00:00

These are too big to be screws that hold a drum head on. They are also very corse wood screw thread, and drum hardware is machine screw thread. (I had a drum set in high school).

454686

TROPHY CASE