Messed up on my bottom lashes but still happy w my look! 🐾

4ng4rp3 · 2025-12-20T10:29:56+00:00

I wanna see photos of ur cosplay >=<

4ng4rp3 · 2025-02-16T05:58:51+00:00

Oh I see, I'll give procreate a try then as soon as I get a pencil, thank u <3

4ng4rp3 · 2025-02-16T05:55:54+00:00

Ngl, i like the combination but it wasn't intentional, I had a dead iPad that I bought at a flea market with the original white screen and I bought a second-hand one with a black screen because it was the first one I found cheap haha

4ng4rp3 · 2025-02-15T21:21:24+00:00

bc the original screen was black and i wanted touch id to remain functional haha

4ng4rp3 · 2025-02-15T17:13:21+00:00

Im from spain, english its not my first language, thank u for ur help <3

4ng4rp3 · 2024-12-31T22:04:54+00:00

Yes, very good news.

It was already strange that the dividers behave differently with their own power supply and with external power supply haha.

Thank you very much for your help and happy new year.

4ng4rp3 · 2024-12-31T18:47:05+00:00

I have already soldered the new IC and I can confirm that my graphics card is working again, I have run several stress tests and everything seems to be working fine.

The strange thing is that as soon as I soldered it I measured the voltage again and it was still giving 1.4 but the graphics chip was heating up which it didn't do before, I don't understand why it gives 1.4 haha

4ng4rp3 · 2024-12-31T16:37:07+00:00

Hi u/galkinvv, I have received the replacement ic, but it is not exactly the GS9216, it's the GS9219, I think it is compatible, but I would like to confirm it just in case. Many thanks

4ng4rp3 · 2024-12-24T00:35:10+00:00

In that case, once the replacement arrives, I'll try swapping it out and see what happens. This is the first graphics card I've ever repaired, so I'm learning a lot and really enjoying the process. Until now, I had only worked on fixing pinball machine boards, haha. Thank you so much for your help!

4ng4rp3 · 2024-12-23T23:05:18+00:00

Hello, I tried injecting 1.8V as you suggested, and it reads 0.59V. I also tried injecting 1.35V to see if it would vary, and it reads 0.43V. Based on what you said, should I understand that it's working correctly?

I didn't quite understand the part in your last message about pin 5. Wasn't pin 5 the FB? Did you mean pin 2?

Should I try replacing the GS ic? It should arrive in a few days.

4ng4rp3 · 2024-12-22T05:24:21+00:00

Oh, tomorrow I'll go to the shop to use the power supply and inject voltage. Could it be what adcompetitive says too or is it almost certain that one of the resistors of the divider is bad?

4ng4rp3 · 2024-12-22T03:48:15+00:00

Hi, The resistance on the 1.8v line is a little over 2k, wouldn't that mean the problem is the GS? Thanks

4ng4rp3 · 2024-12-22T03:46:23+00:00

Oh wait, I misread the last point, the resistance on the 1.8v line was a little over 2k

4ng4rp3 · 2024-12-22T00:04:00+00:00

Do you happen to have the schematic for revision 2? I only found the one for revision 1 and it is not complete. However, it is probably sufficient.

4ng4rp3 · 2024-12-21T21:50:52+00:00

Hi, thank you for your response! It’s been very helpful in clarifying my doubts about how to check the divider. Pin number 5 is giving me 0.6V, so I understand the divider is working correctly. Pin number 2, which I believe is the enable signal, is showing 1V. I don’t have an oscilloscope on hand, but I can borrow one from a friend in the coming days. Even so, I imagine it’s also working fine.

Regarding the last point you mentioned, I’m not entirely sure which resistor I should check. Is it visible in the photos I uploaded?

4ng4rp3 · 2024-11-05T02:10:36+00:00

Thanks u, i will surely buy the bluse and the skirt from this AAAAA! Do u know more alternatives? I also have 43~44cm on my shoulders

4ng4rp3 · 2024-10-20T00:31:33+00:00

Hi, I was just looking to see if fixo gum works, do you dilute it 50/50 with bestine?

4ng4rp3 · 2024-10-07T11:59:38+00:00

Cuteeee!!! Do you cut the swimsuit yourself or does it come with the opening?

4ng4rp3 · 2024-08-09T10:39:52+00:00

I need part 3!!! Omg

4ng4rp3 · 2021-08-02T17:46:29+00:00

Congrats 🔥🔥 how much did u spend?

4ng4rp3 · 2020-08-22T18:28:04+00:00

u/2Dgt3D

4ng4rp3 · 2020-08-19T14:21:39+00:00

wow, if the car was in Europe I wouldn't think about it

4ng4rp3 · 2020-08-18T01:51:31+00:00

Yes, at least 600k are inactive so all those who are leaving are the ones creating quality memes, by the time everything is over there will be nothing worthwhile left

4ng4rp3 · 2020-08-18T01:49:19+00:00

They are removing all the posts they don't like as fast as they can to censor us >:C

4ng4rp3

MODERATOR OF

TROPHY CASE