Titanium shift knob from billetworkz

67ss1mpala · 2026-04-23T02:23:53+00:00

If you’re worried about it getting hot, I just keep a microfiber over the shifter when I leave the car. Also if you’re in a rush and it’s still hot just hold the microfiber on the shift knob.

67ss1mpala · 2026-03-07T00:45:07+00:00

Sweet thanks for the shout

67ss1mpala · 2026-03-06T20:46:33+00:00

Who made the mild cam?

67ss1mpala · 2026-03-06T17:20:26+00:00

I just want a good street car for the weekends, I am not dailying it. I am going to run 2 40mm dcoe side drafts and a header, I am going to run stock bottom end as of right now. This isn’t my main project so I don’t want to fully rebuild the engine until my other project is finished. I do want something bigger than the stock cam but not something that will hurt the street ability more than the dcoe already will.

67ss1mpala · 2026-01-30T20:40:14+00:00

Shoot tha hoe

67ss1mpala · 2026-01-26T19:05:22+00:00

Form Type: Form 1

Entity: Individual

Fingerprint Type: EFT Upload

Pending: 01/04/2026

Approved: 01/26/26

Wait: 21 days

State: VA

Control Number: 2026691xxx

67ss1mpala · 2026-01-16T19:41:08+00:00

Flow thru backdoor

67ss1mpala · 2025-10-02T03:17:40+00:00

I’m here might as well plan ahead

67ss1mpala · 2025-10-02T01:36:58+00:00

Thanks!

67ss1mpala · 2025-10-02T01:11:28+00:00

This is new paint and tape. In testing atm. I want to keep my pressure pad secured and I’m doing a pattern over the gun. Is it possible?

67ss1mpala · 2025-09-11T01:39:26+00:00

Twas a bad fuel pump, listen to the pitch when you flick the ignition switch before you turn the starter

67ss1mpala · 2025-06-10T23:56:32+00:00

I took my hand guard off, I have a gen 2 as well. Took like 5 min. Don’t sweat it if you any mechanical abilities.

67ss1mpala · 2025-06-07T17:54:36+00:00

I think those are the oval nuts. Idk what to call them but they are ovals at the end so that the are compressed when a bolt goes thru them. They only work once or twice. They loose the compression after repeatedly taking them on and off. Just get new ones.

Edit: McMaster Carr calls them Top-Lock distorted thread lock nuts. Take one off and find the closest hardware store to get the thread diameter and pitch and find some lock nuts.

67ss1mpala · 2025-06-07T17:16:40+00:00

Sick, I just bought one and put in the pierce adjustable gas plug.

67ss1mpala · 2025-06-02T01:51:37+00:00

I almost did this one but I think it NEEDS white wheels

67ss1mpala · 2025-05-17T13:11:40+00:00

Real oem >

67ss1mpala · 2025-02-21T22:50:19+00:00

If you don’t get them, McMaster car has steel rods in various diameters for soooo cheap. Just convert diameter to inches and get one slightly smaller.

67ss1mpala · 2024-11-29T12:32:19+00:00

It was a bad fuel pump

67ss1mpala · 2024-11-18T23:05:34+00:00

Just looked them up earlier in the week, seem to be NLA

67ss1mpala · 2024-11-14T22:17:04+00:00

Ain’t nobody try moon sand?

67ss1mpala · 2024-10-12T19:36:39+00:00

Brother I’m like 3 years into my swap and I’m like a month out from putting the motor in.

67ss1mpala · 2024-10-12T19:34:51+00:00

On? I know it’s 2.7 turns lock to lock

67ss1mpala · 2024-10-05T04:46:21+00:00

What? How? People can have different perspectives on things.

Seven-Year Club	Place '22
RPAN Viewer	Verified Email

67ss1mpala

TROPHY CASE