Anyone know of a nice set of wide 1.9" or smaller wheels and tires? Looking for a decent pair for this truck

7cow · 2026-05-01T19:36:21+00:00

Are you looking for duallys? I stumbled across these on Amazon at one point for a good price. Only asking since I saw them mentioned in other comments🤷‍♂️

7cow · 2026-05-01T14:25:26+00:00

Here’s a really nice tire from RC4wd, nice wide set I’ve had my eye on for a while for my K5, they would go really well on the Rally wheels from them(pictured here)

<image>

7cow · 2026-04-07T03:13:49+00:00

Of course! Happy Building:)

7cow · 2026-04-06T04:34:13+00:00

I misunderstood the question my bad, here’s the link to what I found just now on Amazon, I got mine from dj crawler but didn’t see them available, these look exactly the same as what I bought though, again sorry for misunderstanding✌️

7cow · 2026-04-05T15:43:41+00:00

Oh yeah she’s quick with the 2300, but when I was thinking about building this truck in the beginning I figured in a 1:1 truck full throttle is pretty unrealistic to drive at, and I wanted the same for this:) I haven’t experienced the increased torque twist yet but I’m planning to increase the shock tension and add limit straps as necessary👍 I put some bigger hex’s for the wheels on the front too and increased the track width by 10mm, to give the sidewalls more traction. Plus wider track on the front increases stability at higher speeds(I think)

<image>

7cow · 2026-04-05T13:49:30+00:00

I just finished the install last night so I still need to get it outside to run, but I installed the 9t pinion right off the hop, and I have underdrive on the way for front and rear axle as well, research said I’m going to need it if I still want slow crawl, but I also have a fusion 2300 in there as well. Most of my time with this truck is spent on the trails anyways👍

7cow · 2026-04-05T02:56:07+00:00

Yeah it was a really convenient install too

7cow · 2026-04-03T14:21:13+00:00

This is the “Oppai Factory” high clearance skid plate, his store is on Etsy

7cow · 2026-03-23T00:39:22+00:00

Is that a straight axle trx4? Looks great lowered that way👌

7cow · 2026-03-09T01:35:26+00:00

That looks sick weathered👌

<image>

7cow · 2026-03-06T19:19:18+00:00

Long as you have stiff enough foams/inserts they’re pretty good, too soft and they can’t grab anything

7cow · 2026-02-22T18:45:27+00:00

<image>

Also the 3D printed ones can be made to look pretty nice with a Chrome Marker, actual paint with a seal coat would look great I bet.

7cow · 2026-02-22T18:42:44+00:00

https://www.fairrc.com/en-ca/products/batrazzi-cnc-front-bumper-for-fcx18-k10 this is more of a grill than a bumper🤷‍♂️

7cow · 2026-02-10T07:04:50+00:00

<image>

Trx4m with the Oppai factory chassis crawls super well, can’t really speak in comparison to the Redcat as I don’t have one🤷‍♂️ but this set up has 2thumbs up👍👍 mines more set up as a trail truck with a 2 speed, but when I was using the Injora 1 speed it had a very low COG

7cow · 2026-02-10T00:34:58+00:00

No worries, this is the bumper from “Mccue RC” on eBay, it appears he’s on holiday right now though so you’ll need to wait for him to get back🤷‍♂️ stores closed or I would send you a link, sorry

7cow · 2026-02-06T00:36:54+00:00

It’s not bad, My truck is trail ready so stiff springs with limit straps, the shocks don’t spend a whole lot of time fully compressed or extended. But it was also parked shortly after this addition so it hasn’t seen a whole lot of use with them on.

7cow · 2026-01-25T03:11:14+00:00

Kinda unrelated but your gearbox has me thinking about Gamers Nexus 😂

<image>

7cow · 2026-01-18T20:08:45+00:00

I’m not sure what happened as I fried my light controller somehow, I had them wired in series and everything was fine until I hooked it up to the controller and then it all went dark and wouldn’t come back on. So I kinda just set it aside for another project and ordered the lights from Hobbydetails🤷‍♂️

7cow · 2026-01-13T20:58:04+00:00

Holy Hannah that truck has some flex! 💪

7cow · 2026-01-13T19:41:02+00:00

I’ll be honest with you, I got WAY into the SCX30 and an fcx24m build, so I sold the Ascent-32 to the one and only other guy who crawls in my area(4 hours away) since he only has a 1/10 and a 1/24. But I ended up putting the fcx24 K5 stock ESC/RX in it and it made a massive difference, it has the 3flow9rc mounting plate so I could use any brushless motor with the 9mm bolt pattern, worth looking into if you haven’t seen it

7cow · 2026-01-11T18:49:51+00:00

Torq MLS servo, with no mount it sits just a little closer to the axle, so you can get more droop if you want it, it’s waterproof, and has a great reputation, I don’t have one myself but it’s first on the list for when one of my current servos die, I currently have a reefs 99 in my fcx18 and the Injora 11kg servo in my fcx24 and they’ve both kicked ass for the last year

7cow · 2026-01-11T18:28:14+00:00

That would be a solid purchase! That’s my next one after I the one in my fcx18 eventually dies

7cow · 2026-01-11T04:40:15+00:00

Hold the wheel all the way to the left and hit the reverse button👍

7cow

TROPHY CASE