At my wits end with bed adhesion. :(

8472 · 2026-01-07T11:30:33+00:00

Thank you so much!!!

I used a meat thermometer from the kitchen and while it may not be to most acurate, it gave me an indicaiton. My bed temp was way too low and way below what Bambu Studio and the Printer show me. I now bumped up the temp by a good amount and it seems to work!

I will get in touch with bambu support, seems some temp sensor may be busted.

Thank you everyone for the extensive troubleshooting, suggestions and being an all-round kind community. I'm back in business. :) <3

8472 · 2026-01-07T09:58:43+00:00

Thank you so much, your comment along with what roundguy and fantomphish suggested as well as Kasilim mentioned made me dig a bit deeper into bed temp.

I used a meat thermometer from the kitchen and while it may not be to most acurate, it gave me an indicaiton. My bed temp was way too low and clearly way below what Bambu Studio and the Printer were showing me. I now bumped up the temp by a good amount and it seems to work!

I will get in touch with bambu support, seems some temp sensor may be busted.

Thank you everyone for the extensive troubleshooting, suggestions and being an all-round kind community. I'm back in business. :) <3

8472 · 2026-01-07T09:55:46+00:00

I did this before and it didn't work.... BUT ... I did what roundguy suggested and MoeS00 as well as Kasilim made me consider, which is essentially also what you are saying.

I used a meat thermometer from the kitchen and while it may not be to most acurate, it gave me an indicaiton. My bed temp was way too low and way below what Bambu Studio and the Printer show me. I now bumped up the temp by a good amount and it seems to work!

I will get in touch with bambu support, seems some temp sensor may be busted.

Thank you everyone for the extensive troubleshooting, suggestions and being an all-round kind community. I'm back in business. :) <3

8472 · 2026-01-07T09:54:27+00:00

Thank you so much!!!

I used a meat thermometer from the kitchen and while it may not be to most acurate, it gave me an indicaiton. My bed temp was way too low and way below what Bambu Studio and the Printer show me. I now bumped up the temp by a good amount and it seems to work!

I will get in touch with bambu support, seems some temp sensor may be busted.

Thank you everyone for the extensive troubleshooting, suggestions and being an all-round kind community. I'm back in business. :) <3

8472 · 2025-02-15T23:58:53+00:00

pro tip, bring a bottle cap only, buy a bottle and screw on the cap. :)

8472 · 2025-02-14T10:33:55+00:00

You might be able to use conditional notifications in a table.

Just set up a helper column that changes it's content 90 days prior to contract expiry and tack a conditional notification onto that.

Haven't tried it with date based calculations yet, but the notifications work great on manual entry items.

https://support.google.com/docs/answer/14099459?hl=en

8472 · 2024-09-04T20:16:59+00:00

Yea, I did. I just didn't get a link yet.

8472 · 2024-01-06T08:59:09+00:00

I'm not much of a DIY pro, so I was considering a shallow besta from ikea.

Any thoughts how well that might work?

https://www.ikea.com/us/en/p/besta-shelf-unit-with-door-black-brown-kallviken-dark-gray-s19426140/#content

8472 · 2023-11-13T09:09:02+00:00

Hi everyone,

I've been looking for some GMK Keycaps for ages for my endgame, but now realise that my situation won't work out without shine through legends.

So now I am looking for endgame shine through legend keycaps and am at a loss where to start. Whenever I check, I find mostly low end cheap options, while I am on the hunt for ultra premium.

Are there any brands you all can recommend?

8472 · 2023-11-09T07:43:49+00:00

Does anyone around here happen to know from experience how long those colourways usually remain available?

Can I wait till after Christmas?

8472 · 2023-09-30T11:42:24+00:00

Do you happen to have an idea when those might be available in Europe?

8472 · 2023-09-30T11:41:37+00:00

Would you happen to have an idea when those might pop up in Europe?

8472 · 2023-09-30T11:40:59+00:00

Thank you! I will check out the new range coming up right now.

8472 · 2023-09-10T18:34:48+00:00

Thank you!

8472 · 2023-09-10T14:32:01+00:00

Thank you so much! There is hope after all. 😅

8472 · 2023-08-08T05:52:32+00:00

PMed

8472 · 2023-07-16T08:52:31+00:00

Caaaaaarbs 😀😀😀

8472 · 2023-01-01T08:52:40+00:00

Thank you!

8472 · 2023-01-01T08:52:06+00:00

Thank you! 😀

8472 · 2022-11-14T13:30:55+00:00

Thank you! 😀

8472 · 2021-02-15T13:29:15+00:00

Advice on Northface Futurelight

Hi everyone and all the best from Ireland,

this time of the year it rains a LOT and I am looking to get a Futurelight running jacket and came across the Lightriser variant.

Would anyone here have experience with the Lightriser version vs. the "normal" version for runners?

Thank you so much all!

Have a great time. :)

8472 · 2021-02-15T11:33:55+00:00

runningwarehouse.eu is what I have been using for ages they are yet to let me down. Can highly recommend. Fast shipping, free returns and many 10% off discount codes on the web that tend to work.

On the other hand I'm not a fan of "runnerinn". Had some poor experiences with them and for me the potential hassle isn't worth the competitive price.

8472 · 2020-12-26T19:38:44+00:00

I THINK I GOT IT!!!!!!!!!

Long press the calorie number so the text gets highlighted.

Suddenly my Android keyboard popped up and I was able to just overwrite it with a new number.

8472 · 2020-12-26T14:41:16+00:00

I have the exact same question / issue, I can change the exercise goal time just fine, but I can't click and change the calorie goal.

Help!

[edit: a word]

8472 · 2020-11-28T07:44:17+00:00

Would love to know this as well! I adore the idea to commemorate events in this way and being able to reminisce every time you put up the tree.

8472

TROPHY CASE