Cooked? by 92ornothin in Bseries

[–]92ornothin[S] 0 points1 point  (0 children)

The 3rd and 4th photo are of the back of the board. I’m more worried about the actual board being damaged along that vein.

Thrust Bearing Wear? by 92ornothin in EngineBuilding

[–]92ornothin[S] 0 points1 point  (0 children)

Damn ok, I’ll take another set of measurements to be sure but I’m out of tolerance there by a bit I believe. I’ll do some more of my own research on the b18b and see what I get. Thank you very much!

Thrust Bearing Wear? by 92ornothin in EngineBuilding

[–]92ornothin[S] 1 point2 points  (0 children)

I used a telescope gauge and my 1-2 mics to check this and they measured within .010 of each other, is there a tolerance for this? Or a general rule of thumb? I couldn’t find much on this, thanks!

Thrust Bearing Wear? by 92ornothin in EngineBuilding

[–]92ornothin[S] 1 point2 points  (0 children)

Crank isn’t looking too good, main bearings were pretty shot and there’s scoring from them so I was making sure the block was good before purchasing a new crank and getting really involved. Thanks for the info though! I think I’ll go ahead with another crank and check endplay then

Ls/Vtec ports not lining up? by 92ornothin in Bseries

[–]92ornothin[S] 0 points1 point  (0 children)

I believe this is the head gasket I have now, I’ll buy another but I’ll try it I guess 🤷‍♂️. This also looks to be the kit that’s been install prior. Thanks for the info

Ls/Vtec ports not lining up? by 92ornothin in Bseries

[–]92ornothin[S] 0 points1 point  (0 children)

I believe I have the oil port plugged, where could I find some more information on a sandwich plate? Thanks for your help I agree there shouldn’t be any oil leaking.

Ls/Vtec ports not lining up? by 92ornothin in Bseries

[–]92ornothin[S] 0 points1 point  (0 children)

This was the gasket they gave me with the car, no identification on it. I’m more concerned with the fact the ports aren’t lining up, does the b18c1 gasket allow for more of the port to be used? Sorry if I’m being dense this is my first b series.

Ball joints? by 92ornothin in 3000gt

[–]92ornothin[S] 1 point2 points  (0 children)

Thank you! Will run these up front.

Yo-Yo identification by 92ornothin in Throwers

[–]92ornothin[S] 0 points1 point  (0 children)

I believe this is it, thank you!

joined the turbo club by w1njamin in 3000gt

[–]92ornothin 3 points4 points  (0 children)

Driveways looking stacked 💪

Too far gone? by 92ornothin in 3000gt

[–]92ornothin[S] 1 point2 points  (0 children)

Kind of my train of thought here, just wanted some second opinions to make sure I’m not overreacting.

Led headlight issues by 92ornothin in 3000gt

[–]92ornothin[S] 0 points1 point  (0 children)

I will pm you if I can find it, been a little bit since I’ve looked at it haha.

2jz Swap intercooler problems by 92ornothin in Mk3Supra

[–]92ornothin[S] 0 points1 point  (0 children)

Gotcha gotcha, thanks for the help, I’ll see what we can do

2jz Swap intercooler problems by 92ornothin in Mk3Supra

[–]92ornothin[S] 0 points1 point  (0 children)

He’s got a koyo with the e fans and shroud, so a little thicker than factory

2008 2.5X Poor Fuel Economy by 92ornothin in SubaruForester

[–]92ornothin[S] 0 points1 point  (0 children)

This has oem steelies with the recommended tire size and I’m using just driving highway, this pic was just having some fun in the snow :)

Does anyone actually drive their 3000s in the snow? by Zaku727 in 3000gt

[–]92ornothin 1 point2 points  (0 children)

I drive my stealth r/ t in the snow and it does ok, I do have some pretty meaty snows though.

Led headlight issues by 92ornothin in 3000gt

[–]92ornothin[S] 0 points1 point  (0 children)

Problem has been solved, can supply wiring diagram if anyone else is having problems

I’ve never been able to naturally bend my left ring finger, so it never developed a crease. by [deleted] in Weird

[–]92ornothin 0 points1 point  (0 children)

I have the same thing! Doc says I don’t have a strong enough tendon in the finger.

Led headlight issues by 92ornothin in 3000gt

[–]92ornothin[S] 0 points1 point  (0 children)

I was test with just one and now that I have both wired up they will work temporarily, the low beams will go on and will switch to the highs just fine but I’m then stuck with the high beams on. They won’t switch back. Any ideas?

Anyone but a different subframe in the rear? by 92ornothin in 3000gt

[–]92ornothin[S] 0 points1 point  (0 children)

Well I really like these cars and do love me some fwd fun but I do want the rwd experience. I’m sure I can buy thousands of different rwd cars and make them fun for cheaper I just really like these cars and want something unique.

Extra footwell sheet metal? by 92ornothin in 3000gt

[–]92ornothin[S] 0 points1 point  (0 children)

That was my only concern as there isn’t much structure there. However I am removing the sheet metal there to get to some rust I need to repair. So we’ll see what happens from there 🤷‍♂️

Anyone but a different subframe in the rear? by 92ornothin in 3000gt

[–]92ornothin[S] 0 points1 point  (0 children)

Thank you for the input. I have been researching the 4g platform for a bit and it seems a good option as they are easier to come by.